REDSTONE 3901216924, Перевод оригинального руководства пользователя

Страница: 30 / 48

30 | GB
• Use the handle (1) to angle the machine head (5)
to the left/right, until the pointer (20) indicates the
desired angle measurement on the scale (19). (in
this connection see also section 8.6).
• Re-tighten the locking lever (22).
• Cut as described under section 8.4.
8.8 Limiting the cutting depth (Fig. 3)
• The cutting depth can be infinitely adjusted using
the screw (26). To do this loosen the knurled nut on
the screw (26). Move the stop for the cutting depth
limitre (27) to the outside. Turn the screw (26) in
or out to set the required cutting depth. Then re-
tighten the knurled nut on the screw (26).
• Check the setting by completing a test cut.
8.9 Sawdust bag (Fig. 2)
The saw is equipped with a debris bag (21) for saw-
dust and chips.
Squeeze together the metal ring on the dust bag
and attach it to the outlet opening in the motor area.
The debris bag (21) can be emptied by means of a
zipper at the bottom.
8.10 Changing the saw blade (Fig. 15-18)
Remove the power plug!
Important. Wear safety gloves when changing
the saw blade. Risk of injury!
• Blade guard (6) open
• Loosen the screw (36)
• Blade guard (6) upwards until it is held
• Firmly press the saw shaft lock (4), and slowly turn
the flange screw (32) clockwise. After max. one
turn, the saw shaft lock (4) engages.
• Then undo the flange screw (32), by applying a
slightly greater force in a clockwise direction.
• Fully unscrew the flange screw (32) and remove
the outer flange (33).
• Then remove the saw blade (7) from the inner
flange (39) and pull out in a downwards direction.
• Carefully clean the flange screw (32), outer flange
(33) and inner flange (39).
• Insert the new saw blade (7) in the reverse se-
quence and tighten.
• Position the guide bar (40) on the pin (36) again,
and secure.
• Important! The cutting angle of the teeth, in other
words the direction of rotation of the saw blade
(7) must coincide with the direction of the arrow
on the housing.
• Before continuing your work make sure that all
safety devices are in good working condition.
• Important! Every time that you change the saw
blade (7), check to see that it spins freely in the
table insert (11) in both perpendicular and 45° an-
gle settings.
• Important! The work to change and align the saw
blade (7) must be carried out correctly.
8.11 Using the laser (Fig. 2)
• To switch on: Move the ON/OFF switch of the la-
ser (35) to the “I” position. A laser line is projected
onto the material you wish to process, providing
an exact guide for the cut.
• To switch off: Move the ON/OFF switch of the la-
ser (35) to the “0” position.
9. Transport (Fig. 1, 2)
• Tighten the locking handle (13) in order to lock the
rotary table (16)
• Press the machine head (5) downwards and se-
cure with the safety pin (24). The saw is now
locked in its bottom position.
• Fix the saw’s drag function with the locking screw
for drag guide (23) in rear position.
• Wearing the machine at the transport handle (44).
• When reassembling the equipment proceed as de-
scribed under section 8.1.
10. Maintenance
m
Warning! Prior to any adjustment, maintenance or
service work disconnect the mains power plug!
General maintenance measures
Wipe chips and dust off the machine from time to
time using a cloth. In order to extend the service life
of the tool, oil the rotary parts once monthly. Do not
oil the motor.
When cleaning the plastic do not use corrosive prod-
ucts.
Brush inspection
Check the 2 carbon brushes (42) after the first 50
operating hours with a new machine, or when new
brushes have been fitted. After carrying out the first
check, repeat the check every 10 operating hours.
If the carbon is worn to a length of 6 mm, or if the
spring or contact wire are burned or damaged, it is
necessary to replace both brushes. If the brushes
are found to be usable following removal, it is pos-
sible to reinstall them.
Service information
Please note that the following parts of this product
are subject to normal or natural wear and that the fol-
lowing parts are therefore also required for use as
consumables.
Wear parts*: Carbon brush, saw blade, table inserts,
dust bags
* Not necessarily included in the scope of delivery!