9
The Security Code determines the programming mode and the accessibility
of programming parameters. This code can be used along with the Program
Mode Lock-out (
P-Loc
) in the User Input Function parameter (Module 1).
Two programming modes are available. Full Programming mode allows all
parameters to be viewed and modified. Quick Programming mode permits only
the Setpoint values to be modified, but allows direct access to these values
without having to enter Full Programming mode.
Programming a Security Code other than 0, requires this code to be entered
at the
CodE
prompt in order to access Full Programming mode. Depending on the
code value, Quick Programming may be accessible before the
CodE
prompt
appears (see chart).
PROGRAMMING SECURITY CODE
000
to
999
USER INPUT
FUNCTION
USER INPUT
STATE
SECURITY
CODE
MODE WHEN “SEL”
BUTTON IS PRESSED
FULL PROGRAMMING
MODE ACCESS
0
Full Programming
Immediate Access
not
P-Loc
______
1-99
Quick Programming
After Quick Programming
with correct code entry
at
CodE
prompt *
100-999
CodE
prompt
With correct code entry
at
CodE
prompt *
0
Programming Lock
No Access
Active
1-99
Quick Programming
No Access
P-Loc
100-999
CodE
prompt
With correct code entry
at
CodE
prompt *
Not Active
0-999
Full Programming
Immediate Access
* Entering Code 222 allows access regardless of security code.
6.3 Module 3 - d
iSplay
and
f
ront
p
anel
B
utton
p
araMeterS
(
3-dSP
)
SEL
Pro
Front Panel
Display
Select Enable
Display
Update Time
Front Panel
Reset Enable
Programming
Security Code
Zero Display
W/Display
Reset
Display
Color
Units
Indicator
Selection
Backlight Unit Only
3-dSP
dSP-t
SEL
rSt
ZErO
UNItS
COLOr
CodE
Display
Intensity
Level
d-LEV
ScroL
Display
Scroll
Enable
PARAMETER MENU
The
yES
selection allows the
SEL
button to toggle through the enabled
displays.
FRONT PANEL DISPLAY SELECT ENABLE (SEL)
This selection allows the
RST
button to reset the selected value(s).
FRONT PANEL RESET ENABLE (RST)
The
yES
selection allows the display to automatically scroll through the
enabled displays. The scroll rate is every 4 seconds. This parameter only appears
when the MAX or MIN displays are enabled.
DISPLAY SCROLL ENABLE
NO
yES
dSP
NO
HI
LO
HI-LO
NO
yES
This parameter activates the Units Indicator on the display. There are two
methods of selecting the Indicator. List will present a group of Units
preprogrammed into the meter. Segments allows the user to choose which of the
segments should light.
UNITS INDICATOR SELECTION
LISt
SEGS
OFF
Enter the desired display color, red or green. This parameter is active for
backlight units only.
DISPLAY COLOR (BACKLIGHT UNIT ONLY)
6rn
rEd
Enter the desired Display Intensity Level (1-5). The display will actively dim
or brighten as levels are changed. This parameter is active for backlight units only.
DISPLAY INTENSITY LEVEL (BACKLIGHT UNIT ONLY)
1
to
5
1
dSP-t
yES
SEL
dSP
rSt
NO
ScroL
This parameter enables the
RST
button or user input to zero the input display
value, causing the display reading to be offset.
Note: For this parameter to operate, the
RST
button or User Input being used
must be set to
dSP
and the Input value must be displayed. If these conditions are
not met, the display will not zero.
ZERO DISPLAY WITH DISPLAY RESET
NO
yES
NO
ZErO
OFF
UNItS
rEd
COLOr
5
d-LEV
000
CodE
DISPLAY UPDATE TIME
This parameter sets the display update time in seconds.
1
0.5
2
seconds
