Redexim Verti-Drain 7120 Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 26

Redexim Verti-Drain 7120 Скачать руководство пользователя страница 10

10

Fig. 9

3.0 GENERAL PARTS LIST

Figure 9 shows some important parts:

1. Safety decal RA, read user manual before use / Toolbox with tools and manual.
2. Safety sticker 911.280.402: keep a distance of at least 4 metres from the machine. Stop

the engine before carrying out repairs or adjustments.

3. Safety decal 911.280.404, the back cover must always be closed and undamaged during

operation of the machine!

4. Safety decal 900.280.404, Be careful not to get pinched when opening rear cover!

* Make sure all decals are clearly visible on the machine and are understood.

5. The serial number is on the inside of the machine.
6. Operating-depth indicator. Attention: the indication is based on the maximum length of

the pins.

7.  Pin angle adjustment spindles.
8.  Three-point fastening pins.
9.  PTO protective cover on the machine.
10. PTO input shaft.
11. Star button/nut for securing the back cover of the Verti-Drain

®

.

12. Adjustable back-roller scraper.
13. Pin angle adjustment indicator.
14. Depth adjustment of the spindle.

«
...
8
9
10
11
12
...
»

Содержание Verti-Drain 7120



























Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды