Redexim VERTI-CUT 2000 Скачать руководство пользователя страница 18

Страница: 18 / 19

Time schedule/frequency Checkpoint/Lubrication

point

Method

After

every

100 operation

hours or annually

Check the roller bearings
and the drive line.

Check for loose bolts / nuts.

Check for oil leaks.

Check the oil level in the
gearbox.

Check hydraulic oil levels.

Use EP2 lubricating grease.

Replace if necessary.

Tighten the loose nuts /
bolts.

Repair or replace.

Use SAE 90 for the
gearbox.

Use Tellus 46 for the
hydraulic system.

After

every

500 operational

hours or annually

Replace the oil in the
gearbox.

Replace the hydraulic oil.

Use 80W90 for the
gearbox. Replenish up to
level plug.

Use Tellus 46 for the
hydraulic system.

After

every

1000 operational

hours

Replace hydraulic filter.

Use original filter (see parts
page).

Used oil / grease constitute an environmental hazard and must be disposed in
accordance with current regulations.

Содержание VERTI-CUT 2000




















Результаты поиска

Содержание VERTI-CUT 2000

Отзывы:

Бренды по названию

Популярные бренды

Redexim VERTI-CUT 2000, Руководство пользователя и каталог запчастей

Результаты поиска

Содержание VERTI-CUT 2000

Отзывы:

Бренды по названию

Популярные бренды