Redexim VERTI-CUT 2000 Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 19

Redexim VERTI-CUT 2000 Скачать руководство пользователя страница 13

13

4.

Connect the machine to the tractor (see section 4.0 - connection to the tractor).

Use the correct tractor; see specifications.

Switch the tractor off and secure the tractor/Verti-Cut combination to prevent

activation/slipping.

4.0 CONNECTING / DISCONNECTING THE VERTI-CUT

Check procedure before proceeding to connect the Verti-Cut.



Check the Verti-Cut for visual damage and repair this damage if the safe
operation of the machine is no longer guaranteed.



Check that all nuts and bolts are properly secured.



Check that all safety guards and all safety stickers are in place on the

machine and are not damaged.
The machine must

NEVER

be used without these.

Fig. 10

The Verti-Cut can be connected to the tractor using the 3-point coupling.

The method is as follows:

(Fig. 10)

1.

Carefully reverse the tractor into a suitable position for connecting the lower

connecting arms to the frame.

!! Ensure that that tractor is properly blocked and cannot move

independently !!

!! Switch the tractor engine off before getting off the tractor !!

2.

Connect the lower connecting arms using the 3-point pins (1) and secure this using

the locking pins provided.

3.

Connect the top rod (2) to the frame using pin (3); secure pin (3) using the locking pin

provided.

«
...
11
12
13
14
15
...
»

Содержание VERTI-CUT 2000




















Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды