Redexim Verti-Cut 1300 Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 18

Redexim Verti-Cut 1300 Скачать руководство пользователя страница 13

13

9.0 USING THE VERTI-CUT

Before using the Verti-Cut in a location, you should check the following items:

1.

Are there loose objects in the field? First remove these objects.

2.

Are there slopes? The maximum slope is 20 degrees for this machine.

Always go from top to bottom.

3.

Is there danger of flying objects (e.g., balls) that distract the attention of
the driver? If so, the Verti-Cut

CANNOT

be used.

4.

Is there danger of sinking/sliding away? If so, postpone the processing
until conditions improve.

5.

If the soil is wet, postpone the activities until conditions improve.

6.

Do not make sharp bends and preferably, drive in straight lines; otherwise
you might damage the subsoil.

10.0 START/STOP PROCEDURE OF THE VERTI-CUT

The start procedure is

VERY

important. If this procedure is not executed as described below, serious

damage to the machine / subsoil could be the result.

The start procedure is as follows:

1. Check the Verti-Cut for loose components and look whether all components function properly.

If loose components are observed or components do not function properly,
the problems must be solved

before

using the Verti-Cut!

2. Drive to the spot where the processing should take place.
3. Put the machine on the surface that has to be treated and adjust the working depth of the machine

statically as described in Chapter 6.0.

4.  Lift the machine.
5.  Engage the tractor in the correct gear.
6.  Adjust the tractor engine to around 1200 rpm and engage the PTO.

7. Slowly lower the machine until it reaches the required working depth.
8. Drive forwards and increase the rotational speed until the PTO rotational speed of 540 rpm is

achieved.

9. For the first few meters:

Check whether the required working depth is achieved. If necessary, adjust the working depth as
described in Chapter 6.0.

Stopping occurs as follows:

1. Decrease the engine revs to 1200 rpm.

2.  Lift the machine off the ground.
3.  Switch the PTO off as soon as the knives do no longer touch the subsoil.
4.  Lift the machine even more.
5.  Go to the next location and start again as described above.

It is preferred to drive in straight lines. Otherwise, damage can occur to the
subsoil and/or the machine!

«
...
11
12
13
14
15
...
»

Содержание Verti-Cut 1300



















Отзывы:

Нет отзывов