manualshive.com logo in svg

Redexim Rink DS550SP, Инструкция по эксплуатации и каталог запасных частей

Поделиться
Скачать
Redexim Rink DS550SP Скачать руководство пользователя страница 7

DS550SP 

 

- 7 -

 

3.0 GETTING STARTED 

 

- 

Tighten the wheel nuts. 

 

- 

Check the tyre pressure. 

 
 

Check these points again after the first laden journey! 

 
 

Start the engine 

 

- 

Fill the fuel tank with unleaded gasoline. 

 

- 

Move the throttle control to FAST position. 

 

- 

Press the engine button ON and move the choke control to the left. 

 

- 

Start the engine, repeat if necessary and slightly close choke. 

 

- 

As soon as engine starts, move the choke control back, and with the throttle control set 
the desired speed. 

 

Before starting the motor, it is absolutely necessary that any user must 
have read and understood the included operating instructions of the 
engine manufacturer. 

 
 

4.0 OPERATING 

 

Before every trip 

 
- 

Check the 

RINK DS550SP Disc Spreader

 for visible damage, and repair any damage.

 

 

- 

Check tyre pressure. 

 

-  Check run marks of the conveyor belt, since the conveyor belt must not rub at the side 

adjust if necessary (see page 15). 

 
 

Loading 

 
- 

Note desired maximum ground pressure. 

 

- 

When loading note permitted total weight. 

Содержание Rink DS550SP














































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды