manualshive.com logo in svg

Redexim Rink DS550SP, Инструкция по эксплуатации и каталог запасных частей

Поделиться
Скачать
Redexim Rink DS550SP Скачать руководство пользователя страница 16

- 16 - 

 

DS550PB 

 

Install the conveyor belt  

 
- Remove 

RINK DS550SP Disc Spreader

 from the chassis

.

 

 

-  Disconnect the hydraulic connectors and spreading system (1) by loosening the screws 

(2). 

 

- 

Remove the protective (3) and rubber (4) covers to the right. 

 

- 

Loosen the conveyor belt (7) on both sides by loosening the screw-nuts (8) 

 

- 

Remove the connecting bolts (9) on the hopper (10). 

 

- 

Loosen and remove clamping rings of the bearing (11) (in right direction). 

 

- 

Loosen the screws (13) on the side (12) and pull off completely with bearing (11). 

 

- 

Remove the conveyor belt (7).  

 
 

Installation is in the reverse order. 

 

 

Fig. 

9

: Install the conveyor belt 

 

 

Conveyor belt tightening after installation 

 
-  During the loosened condition of the conveyor belt, on both sides mark a length of 1,000 

mm from the conveyor belt. 

 

-  Tighten the conveyor belt on both sides and evenly with the two tension bolts (see page 

13), until the marked length is stretched to a maximum of 1,003 mm.  

 

-  Let the conveyor belt run for about 30 minutes until it is centred and running between the 

directional control valves, adjust if necessary.  

 

The conveyor belt must not touch the sides, otherwise it will be damaged. 
During readjustment of the belt, gradually tighten the strips of the belt on 
the side.  
 
Tightening too much shortens the life of the conveyor belt!

 

Содержание Rink DS550SP














































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды