15
5.1 MODULE 1 - S
IGNAL
I
NPUT
P
ARAMETERS
(
,"-)&
)
"
#
!'
#"$%&
"
#
'(
()*+,
PAXH INPUT RANGE
PAXH INPUT COUPLE
Select the input range that corresponds to the external signal. This selection
should be high enough to avoid input signal overload but low enough for the
desired input resolution. This selection and the position of the Input Range
Jumper must match.
The input signal can be either AC coupled (rejecting the DC components of
the signal) or DC coupled (measures both the AC and DC components of the
signal). The coupling jumper and the setting of this parameter must match.
dC
or
AC
SELECTION
!'
-./'
-.-/'
-.--/'
RANGE
RESOLUTION
5.000 A
200.00 mA
20.000 mA
2.0000 mA
200.00 µA
200uA
RANGE
RESOLUTION
SELECTION
300.0 V
0--1
20.000 V
/-1
2.0000 V
/1
200.00 mV
0.2u
PAX PARAMETER MENU
PAXT PARAMETER MENU
"
#
0--2
#"$%&
PAXD INPUT RANGE
Select the input range that corresponds to the external signal. This selection
should be high enough to avoid input signal overload but low enough for the
desired input resolution. This selection and the position of the Input Range
Jumper must match.
3-45
1000o
10000 ohm
1000.0 ohm
±200.00 mV
-./2
±2.0000 A
2A
SELECTION
RANGE
RESOLUTION
RANGE
RESOLUTION
SELECTION
100o
300u
100.00 ohm
±300.00 V
±200.00 mA
20u
2u
-./"
±20.000 V
±2.0000 V
±20.000 mA
-.-/"
±2.0000 mA
-.--/"
±200.00 µA
200uA
Refer to the appropriate Input Range for the selected
meter. Use only one Input Range, then proceed to Display
Decimal Point.
"
#
-.-/"
#"$%&
PAXP INPUT RANGE
Select the input range that corresponds to the external signal.
10.000 V
3-2
20.000 mA
-.-/"
RANGE
RESOLUTION
SELECTION
"
#
-.-/2
#"$%&
PAXS INPUT RANGE
Select the input range that corresponds to the external signal. This selection
should be high enough to avoid input signal overload but low enough for the
desired input resolution. This selection and the position of the Input Range
Jumper must match.
RANGE
RESOLUTION
0.02u
SELECTION
±24 mV
-./1
±240 mV
"
#
678
.
69+&
PAXT INPUT TYPE
Select the input type that corresponds to the input sensor. For RTD types,
check the RTD Input Jumper for matching selection. For custom types, the
Temperature Scale parameter is not available, the Display Decimal Point is
expanded, and Custom Sensor Scaling must be completed.
(:8#,
CS-rH
Custom RTD Low
Custom RTD High
N TC
678;
B TC
678<
(:867
Cu427
Custom TC
RTD copper 10
Ω
S TC
678:
R TC
678#
SELECTION
TYPE
TYPE
SELECTION
Ni672
Pt392
RTD nickel 672
RTD platinum 392
K TC
Pt385
6787
6784
RTD platinum 385
C TC
J TC
678
.
E TC
678&
T TC
tc-t
"
#
=>
:(",&
PAXT TEMPERATURE SCALE
Select the temperature scale. This selection applies for Input, MAX, MIN,
and TOT displays. This does not change the user installed Custom Units
Overlay display. If changed, those parameters that relate to the temperature
scale should be checked. This selection is not available for custom sensor types.
°C
°F
"
#
-
?&(+6
0.000
0.0000
0.00
0.0
0
DISPLAY DECIMAL POINT
Select the decimal point location for the Input,
MAX
and
MIN
displays. (The
TOT
display decimal point is a separate parameter.) This selection also affects
#52;?
,
?:+3
and
?:+/
parameters and setpoint values.
For the PAXT, these are only
available with Custom Scaling.
Содержание PAXCDL
Страница 28: ...27 PAX PROGRAMMING QUICK OVERVIEW PAXT O NLY ...
