red lion PAX Lite PAXLHV Скачать руководство пользователя страница 3

1. 

DISPLAY

: 3-digit, 0.56" (14.2 mm) high character, 7-segment Red LED

2. 

POWER

: 115 or 230 VAC, switch selectable. Allowable power line variation 

±10%, 50/60 Hz, 6 VA. Installation Category II, Pollution Degree 2.

Isolation

: 2300 Vrms for 1 min. to input 

Working Voltage

: 300 V max., CAT II

3. 

ACCURACY

: At 23°C, 85% R.H.; ±(0.1% of R 2 digits)

4. 

INPUT IMPEDANCE

: 1 M

5. 

INPUT RANGE

: 0 to 600 VAC max. @ 45 to 500 Hz. Installation Category I

6. 

RESOLUTION

: 1 VAC

7. 

ENVIRONMENTAL CONDITIONS

:

Operating Temperature Range

: 0° to 60°C

Storage Temperature Range

: -40° to 80°C

Operating  and  Storage  Humidity

:  85%  max.  relative  humidity  (non-

condensing)

Temperature Coefficient

: ±150 PPM/°C

Vibration According to IEC 68-2-6: 

Operational 5 to 150 Hz, in X, Y, Z 

direction for 1.5 hours, 2 g’s.

Shock According to IEC 68-2-27: 

Operational 30 g’s, 11 msec in 3 directions.

Altitude

: Up to 2000 meters

8. 

READING RATE

: 400 msec., nominal

9. 

RESPONSE TIME

: 1 sec. nominal for a step change input.

10. 

CERTIFICATIONS AND COMPLIANCES

:

SAFETY

UL Recognized Component, File #E179259, UL61010A-1, CSA C22.2 No. 61010-1

Recognized  to  U.S.  and  Canadian  requirements  under  the  Component 

Recognition Program of Underwriters Laboratories Inc.

UL Listed, File #E137808, UL508, CSA C22.2 No. 14-M95

LISTED by Und. Lab. Inc. to U.S. and Canadian safety standards

Type 4X Enclosure rating (Face only), UL50

IECEE CB Scheme Test Report #04ME11209-20041018

Issued by Underwriters Laboratories, Inc.

IEC 61010-1, EN 61010-1: Safety requirements for electrical equipment 

for measurement, control, and laboratory use, Part 1.

IP65 Enclosure rating (Face only), IEC 529

ELECTROMAGNETIC COMPATIBILITY

:

Emissions  and  Immunity  to  EN  61326:  Electrical Equipment  for 

Measurement, Control and Laboratory use. 

Notes:

1. Criterion A: Normal operation within specified limits.

2.  Criterion  B:  Temporary  loss  of  performance  from  which  the  unit  self-

recovers.

11. 

CONNECTIONS

: High compression cage-clamp terminal block

Wire Strip Length

: 0.3" (7.5 mm)

Wire Gage

: 30-14 AWG copper wire

Torque

: 4.5 inch-lbs (0.51 N-m) max.

12. 

CONSTRUCTION

:  This  unit  is  rated  for  NEMA  4X/IP65  outdoor  use. 

Installation  Category  II,  Pollution  Degree  2.  One  piece  bezel/case.  Flame 

resistant. Panel Gasket and mounting clip included.

13. 

WEIGHT

: 0.65 lbs. (0.24 Kg)

3

g

eneral

 m

eTer

 s

peCifiCaTiOns

a

CCessOries

UNITS LABEL KIT (PAXLBK)

Each meter has a units indicator with backlighting that can be customized 

using the Units Label Kit. The backlight is controlled by a DIP switch.

Class B

EN 55011

Emissions

Emissions:

0.5 cycle; 40 % variation

Criterion A

EN 61000-4-11

Voltage dip/interruptions

3 V/rms 

Criterion A

EN 61000-4-6

RF conducted interference

1 kV L-L, 

Criterion A

EN 61000-4-5

Surge 

2 kV signal

2 kV power 

Criterion A

EN 61000-4-4

Fast transients (burst)

2 kV L&N-E power

10 V/m

Criterion B 

EN 61000-4-3

Electromagnetic RF fields

8 kV air discharge

4 kV contact discharge

Criterion A

EN 61000-4-2

Electrostatic discharge

Immunity to Industrial Locations:

Содержание PAX Lite PAXLHV









Отзывы: