manualshive.com logo in svg

Record 5100 Series, Руководство пользователя, Страница: 15 / 21

Поделиться
Скачать
Record 5100 Series Скачать руководство пользователя страница 15

Operation mode       >

SERVICE STG

Maintenance          >
Functions            >

Configure System

Learning System   >

Parameter            >

PARAMETER

CAN-BUS        >
Input/Output      >

Miscellaneous               >

Entrance System      >

Control Panel         >

Locking              >

MISCELLANEOUS

Alarm display                        >

Push to actuate open            0

Push to actuate close            0
Holding force                    0

Lead time open                     0

Lead time close                     0

Alarm display

Time safety                         18    

Obstruction                           1

Time activation                   18

Obstruction

0  Disabled

1  Enabled

Disabled= Display module 
will not show Obstruction 
error.
Enabled= Display module 
will show Obstruction error.

This parameter is used to replace the factory
telephone number with a custom telephone
number.  This number will be momentarily 
displayed when the unit is switched from 
“OFF” mode, and will periodically flash when 
an Alarm screen is displaying.  Removal of a
custom number will reinstate the factory 800 
number.

Operation mode       >

SERVICE STG

Functions            >

Diagnostics              >

Learning System   >
Parameter            >

Maintenance          >

Maintenance

Cycles1000 Target               >
Weeks         Actual               >

Weeks         Target               >

Reset maintenance              >

Setup maintenance              >

Cycles1000 Actual               >

Reset Maintenance

Are you sure?

Yes

No

The listed parameters in 
the center screen are for 
setting up a maintenance 
program for the unit and 
resetting it after target is 
met.

Operation mode       >

SERVICE STG

Functions            >

Diagnostics              >

Learning System   >
Parameter            >

Maintenance          >

Maintenance

Cycles1000 Target              >
Weeks         Actual              >

Weeks         Target               >

Phone          800 438 1937

Cycles1000 Actual              >

PHONE

800 438 1937

PN

The following screen sequences are not used to modify parameters, but are used to reset 

Operation mode       >

SERVICE STG

Diagnostics              >

Learning System   >
Parameter            >

Maintenance          >

Functions            >

FUNCTIONS

Factory settings     >

Release AKI          >

Learning ELS            >

Learning parameter   >

BAT emerg. reaction  >

Default Settings         >

various door functions as described.

Default settings
Are you sure?

    Yes     

No

Resets Parameters to “Default 
settings” and requires a new 
Calibration run.

Operation mode       >

SERVICE STG

Diagnostics              >

Learning System   >
Parameter            >

Maintenance          >

Functions            >

FUNCTIONS

Factory settings     >

Release AKI          >

Learning ELS            >

Learning parameter   >

BAT emerg. reaction  >

Default Settings         >

Factory settings
Are you sure?

    Yes     

No

Resets Parameters to “Factory 
settings” without requiring a ne

w 

Calibration run.

Содержание 5100 Series






















Отзывы:

Нет отзывов