ReActiveMicro MicroDrive Turbo Скачать руководство пользователя страница 9

Страница: 9 / 55

MicroDrive Turbo

ReActiveMicro

Advanced Features

The

MicroDrive Turbo

uses CompactFlash Cards. Solid State, readily available,

inexpensive, low power, noise free, high degree of durability with a very long
lifespan, superb quality.

For more information on CF Cards see

Compact Flash Overview

at the end of this

manual.

CF Storage - Benefits

Moving software downloaded from the Internet to your Apple II Personal
Computer has never been quicker or easier. Just remove the CF Card
from your

MicroDrive Turbo

, insert it in to your PC Card

Reader, start

CiderPress

. You can read and write directly to

the CF Card. Using your PC for transferring ﬁles and
backing everything up, taking care of your Apple II files has
never been so quick and painless!

Standard IDE Interface

The 40 Pin IDE interface on the

MicroDrive Turbo

is a standard 16-bit IDE port. It is

capable of addressing Primary and Secondary (Master/Slave) IDE storage.

IDE to Dual CF Adapter

The

MicroDrive Turbo

comes standard with a 40 Pin IDE to Dual CF Adapter. Users

can control which of the Two CF Slots is Primary and Secondary using a Jumper on
the Adapter.

Note: The Dual mode feature is only available on Apple II

Personal Computer.

DMA

As the name implies, the

MicroDrive Turbo

performs Direct Memory Access which

bypasses the CPU and allows for an incredible 40% faster read and write speeds
when compared to conventional controllers.

With an accelerator installed in your II

you can boot GS/OS in as fast as 7 seconds!

The DMA option can be turned on or off using the Setup Utility.

Содержание MicroDrive Turbo
























































Результаты поиска

Содержание MicroDrive Turbo

Отзывы:

Бренды по названию

Популярные бренды

ReActiveMicro MicroDrive Turbo, Руководство пользователя

Результаты поиска

Содержание MicroDrive Turbo

Отзывы:

Бренды по названию

Популярные бренды