Reach Technology PoE4N/10G Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 27

Reach Technology PoE4N/10G Скачать руководство пользователя страница 8

Reach PoE4N/10G Tester Manual 1.1

06/15/2020

Page 8

3.3.

UUT Connections

The RT-PoE4N/10G has 24 test ports, configured as 12 pairs (1-2, 3-4, 5-6, etc.). Each

port has the ability to act as a PD load to the UUT. In addition, each port pair can be

configured to pass data from one port to the other via internal straight through

connections, allowing the loads to be applied while passing traffic. All data path

connections are made via signal relays and 100 ohm differential pairs for data integrity.

Connect the port of the PoE supplying device under test to the UUT connector via a

standard straight through Ethernet connector (see the

Ethernet Cables

section for more

information regarding cables). There is an 802.3at class transformer isolating the UUT

ports in each port pair so that power can be tapped from the UUT (see the

section for more details).

Note that the devices connected to any given port pair cannot "see" the power from the

other port. In other words, the UUT ports in a port pair are connected from a data

perspective, and each UUT port connects to the RT-PoE4N/10G active load from a power

(PoE) perspective.

NOTE: with high power loads, the DC balance of the patch cables used is important to

avoid DC saturation of the Ethernet transformers. DC Balance (DC resistance per side

of the power carrying pair) should be within 3%. The standard patch cable

specifications of Cat 5, 5e, and 6 do not specify DC balance.

«
...
6
7
8
9
10
...
»

Содержание PoE4N/10G




























Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды