Reach Technology PoE4N/10G Скачать руководство пользователя страница 6

Страница: 6 / 27

Reach PoE4N/10G Tester Manual 1.1

06/15/2020

Page 6

2.3.

Features



IEEE signature options: nominal, high, and over-spec capacitive.



Classification 0 through 4 (all nominal).



Passes 10GbE traffic from each test port to the neighboring port isolated from PD load
(1-2, 3-4, etc.).



Relay data path for compatibility with Phy-based cable diagnostics.



Low cost compared to compliance-level PD emulators.



Universal voltage (110/220) power supply.



Serial RS232 console control.

2.4.

Dimensions

The unit fits in a standard 19" rack using screw-on ears.

Case outside dimensions are:

16.665" deep
17.30" wide (fits 19” rack; mounting ears provided)
1.74" high

2.5.

Electrical Characteristics

The RT-PoE4N/10G is powered via a locking power DIN 4 pin connector and requires

12V DC at a maximum of 8.5 Amps.

The unit is supplied with a worldwide universal AC input power supply brick. Its

characteristics are:

85-264VAC input, 87.5% efficient, 0 to 40C operation, IEC320/C14 input

2.6.

Environmental

Operating temperature range is 0C to 40C. Storage is -30C to 70C.

Humidity is 85% maximum, non-condensing

2.7.

Warranty

The RT-PoE4N/10G is warranted by Reach Technology against manufacturing defects

for one year.

2.8.

Operating Software

No Software license is required.

2.9.

Calibration

The unit performs self-calibration on power-on, or on command.

Содержание PoE4N/10G




























Результаты поиска

Содержание PoE4N/10G

Отзывы:

Бренды по названию

Популярные бренды

Reach Technology PoE4N/10G, Руководство пользователя

Результаты поиска

Содержание PoE4N/10G

Отзывы:

Бренды по названию

Популярные бренды