manualshive.com logo in svg

Reach Technology PoE4N/10G, Руководство пользователя

Поделиться
Скачать
Reach Technology PoE4N/10G Скачать руководство пользователя страница 19

Reach PoE4N/10G Tester Manual 1.1 

06/15/2020 

Page 19 

CLASS 

Description 

Sets the IEEE load class. See IEEE 802.3af and 802.3at specification 
(external documents).  

Command:   

cl[ass] [0|1|2|3|4]

 

      Argument:   

class value 

 

Response: 

printf(":p%d class %d\n", port, class); 
 

Example:   

p9 cl 3 

Example response:  :

p9 class 3<CR><LF> 

 

 

 

This sets port 9 IEEE "class" to 3. 

 

UPOE 

Description 

Changes between regular PoE, PoE+ mode and UPoE mode. In UPoE 
mode the load is limited to 100mA until power good is detected on both 
pairs. In regular mode the load is limited to 100mA until power good is 
detected on the main pair. If a comma is present the command assumes 
the user is requiring that power be valid on a specified pair before 
releasing the 100mA limit e.g. when “upoe 0,1” is entered then the load 
will be limited to 100mA until power is valid on the alternate pair. 

Command:   

upoe [on|off|0,0|0,1|1,0|1,1]

 

Response:   

printf(":p%d upoe %d\n\r",port,state); 

state

 = 1 or 0 for on and off respectively. 

 

CONNECT  

Description 

Controls the relays that connect the power load circuitry to the UUT port 
via the GbE transformer. From a power perspective, this is equivalent to 
plugging in the RJ45 from the UUT. See the 

Operational Overview

 

section for more details. Connect must be on for the UUT to see an IEEE 
802.3af/at PoE load. The connect command can also be used to select the 
main, alternate, or both power pairs. If a comma is present the command 
assumes the user is specifying the connect status of each pair 
individually. The first value is the connect status of the main pair and the 
second is the alternate pair e.g. when “connect 0,1” is entered then only 
the alternate pair will be connected to the load. 

Command:   

conn[ect] [on|off|0,0|0,1|1,0|1,1]

 

Response:   

printf(":p%d Connect Sig %d\n", port, state); 

state

 = 1 or 0 for on and off respectively. 

 

Содержание PoE4N/10G




























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды