RCA DSA112NW Скачать руководство пользователя страница 69

Страница: 69 / 88

Final Approach

Insert the end of the LNB into the end of the LNB support
arm (push any extra coaxial cable back through the support
arm).

Find the special hex retainer nut and insert it into the LNB
mounting hole on top of the LNB support arm.

Hint:

The hex retainer nut must be inserted into the top of

LNB before the phillips head screw is inserted into the
bottom of the LNB, otherwise it is very difficult to thread the
screw to the nut.

Find the phillips head screw and insert it into the LNB
mounting hole from the bottom of the LNB support arm.
Tighten the screw with a screwdriver

Do you have a pole mount?

YES

Attach the messenger (ground) wire to the metal pole using
a 1-1/2" grounding clamp.

•

Find the 1/4" hex head bolt, the 1/4" self-locking nut, and the
star washer that came in the hardware packet.

•

Place the washer on the bolt, place the bolt in the hole in the
foot of the mast and loosely attach the nut to the bolt.

•

Wrap the messenger (ground) wire around the bolt between
the star washer and the surface of the mounting foot and
tighten the nut.

BOLT

NUT ( insert first )

nut (insert first)

phillips-head screw

Hex head bolt and star washer

Hex head bolt

Wire

Star washer

Self locking nut

wire

hex head bolt &

star washer

wire

hex head bolt

star washer

self-locking nut

IMPORTANT

The National Electrical Code specifies that

coaxial cable that is exposed to lightning shall be connected
to the grounding system of the building as close to the
point of cable entry as possible.

Содержание DSA112NW

























































































Результаты поиска

Содержание DSA112NW

Отзывы:

Похожие инструкции для DSA112NW

Бренды по названию

Популярные бренды

RCA DSA112NW, Руководство по установке

Результаты поиска

Содержание DSA112NW

Отзывы:

Похожие инструкции для DSA112NW

Бренды по названию

Популярные бренды