RCA DSA112NW Скачать руководство пользователя

Страница: 67 / 88

Final Approach

4. Is the bubble centered in the level’s window?

YES

Continue to “Leveling Front-to-Back”.

a) If the bubble is not centered, determine which side of the

mounting foot needs to be raised.

b) Unscrew the lag or machine screws from that side of the

mounting foot.

Place 5/16" washers between the mounting foot and the
mounting surface. Use enough washers to level the
mounting foot.

d) Secure the mounting foot with the lag or machine screws.

Leveling Front-to-Back

Loosen the two bolts securing the mast to the mounting foot
so the mast moves freely.

Place a bubble level on the mast as shown in the figure.
Move the mast so the bubble is centered in the level’s
window.

Tighten the two bolts securing the mast to the mounting
foot.

Add washers
until foot
is level

Rotate mast as needed

Adjustment

Level

Not Level

Rotate mast as needed

Adjustment

Level

Not Level

Содержание DSA112NW

























































































Результаты поиска

Содержание DSA112NW

Отзывы:

Похожие инструкции для DSA112NW

Бренды по названию

Популярные бренды

RCA DSA112NW, Руководство по установке

Результаты поиска

Содержание DSA112NW

Отзывы:

Похожие инструкции для DSA112NW

Бренды по названию

Популярные бренды