background image

12

En el extremo abierto de la sección 
central (grande), retire el tornillo y la tuerca 
posteriores.

Encuentre la sección posterior. Deslice el 
brazo delgado de la antena posterior en la 
sección central (grande). Con un martillo 
de goma, golpee suavemente el extremo 
del brazo pequeño para alinear los orifi cios 
para tornillo. (Consulte la fi gura 6.)

Vuelva a instalar el tornillo y la tuerca; 
asegúrese de apretarlos bien.

Paso 6:   Conecte la sección posterior a la sección 

central (grande)

Sección 
posterior

Sección 

central

Tornillo

Tuerca

Fig. 6

Paso 7: Conecte las líneas de fase

En la sección central (grande), cerca de 
donde se intersectan las secciones central 
y posterior, encuentre los postes en la 
partes superior e inferior de los pernos del 
sujetador del último elemento. (Consulte la 
fi gura 7.)

Coloque las líneas de fase de la sección 
posterior sobre los prisioneros con rosca, 
uno en la parte superior y el otro en la 
parte inferior. Asegúrelas a los prisioneros 
con rosca con las arandelas y tuercas de 
brida #10. Apriételas bien.

Tuerca

Arandela

Prisionero 
con rosca

Línea 
de fase

Fig. 7

5

Step 8: Connect the boom brace  

Lay the boom brace on top of the antenna. Make sure the mast clamps (the 
brass-colored sections) on the boom brace and antenna are facing the same 
direction. 

Locate the screw hole in the refl ector boom 
and attach the brace with one of the provided 
#10 screws and nuts. (See fi gure 8.) 

Screw

Nut

Fig. 9

Fig. 8

Step 9: Install the transformer

Find the downlead connection on the bottom of the front section of the 
antenna, just beyond the refl ector booms. 

Place two washers on each of the studs. Place a #10 nut on top of each stud, 
but don’t tighten them yet. 

Place the transformer ends between the two washers and tighten the nuts 
securely. (See fi gure 10.) Attach the coax downlead to the transformer.

Transformer

Downlead 

connections

Fig. 10

Swing the boom brace down towards the 
rear. Form a “V” with the metal straps. Use 
one of the provided #10 screws and nuts to 
attach the “V” to each side of boom. (See 
fi gure 9.)

English

Содержание ANT3038XR









Отзывы: