background image

2

IMPORTANT: Unfold the elements on each end of 
the refl ector boom so that the front of their locking 
tabs face towards each other. The remaining 
locking tabs can be unfolded in either direction. 
Make sure that all of the elements are perpendicular 
to the refl ector boom.  

Connect the two refl ector booms to the front boom 
using two of the provided #10 nuts and screws. 
The refl ector booms should be parallel to the 
smaller boom at this point. (See Fig. 1.)

Fig. 2

Step 2:   Connect the refl ector booms to the front 

(small) boom 

Find the two refl ector booms and the front (or small) 
boom. The two smaller elements on the refl ector 
booms face away from the small main boom.

Fig. 1

Step 3:  Unfold the rest of the antenna

Unfold all the other elements on the antenna until they lock into place ensuring 
that they are fl at and parallel to each other. (See Fig. 3.)

Fig. 3

Fig. 2A

FRONT

Locking Tab

Main Boom

15

Paso 12:   Acople el conector de conexión coaxial 

al TV o preamplifi cador

Acople el conector de conexión 
coaxial al TV. 

Gire la antena hasta que obtenga 
una imagen óptima. Posiblemente 
necesitará a alguien que se fi je en la 
imagen del TV mientras usted gira la 
antena. 

Fig. 14

Oriente hacia 

las torres de 

difusión

AVISO:

 Oriente el extremo pequeño 

de la antena hacia la emisora(s).

Importante: Oriente la Antena hacia las Torres de Difusión 
Locales

Visite www.antennaweb.org para conocer las ubicaciones de las torres de 
difusión locales. Esta información es sumamente importante para la lograr la 
orientación correcta de la antena.

Paso 13:   Fije las abrazaderas del mástil y el 

conductor de conexión, ponga la antena 
a tierra

Apriete bien las dos abrazaderas del mástil. 

Fije el conductor de conexión coaxial al mástil (utilizando amarras de cable o 
cinta aislante) para evitar que el viento lo derribe.

Ponga a tierra la antena y el mástil observando las instrucciones de puesta a 
tierras adjuntas.

Remoción de la Antena

Siga las instrucciones de instalación exactamente a la inversa para remover 
antena.  Por su propia seguridad, siga las instrucciones para instalar la 
antena comenzando con el último paso.

Español

Содержание ANT3038XR









Отзывы: