RBH Access Technologies Integra32 Скачать руководство пользователя страница 24 | Manualshive

Страница: 24 / 64

RBH Access Technologies Integra32 Скачать руководство пользователя страница 24

Chapter 2
Intelligent Field Panel

Integra32

™

Hardware Guide

RBH Access Technologies Inc.

20

Power

The ELC-08 requires 9 to 14 volts DC (connected to the Data Input) and draws a
maximum of 325ma.

Data Input / Data Output

The  first  ELC-08  is  connected  to  the  Elevator  URC2000.    Four  wires  are connected  as
per the diagram above.  The second, third, and fourth boards are each connected to the
previous  board.    Board  four  connected  to  board  three,  board  three  connected  to  board
two, and board two connected to board one.  Connect 0v to 0v, D+ to D+, D- to D-, and
12v to 12v.

Fire Signal

Apply 12-24 volts DC to satisfy this input. When this voltage is removed all of the
relays on the board will power down (turn ON), making all floors accessible. If the Fire
Signal feature is not required install a jumper on the Fire Signal Bypass.

«
...
22
23
24
25
26
...
»

Содержание Integra32

































































Отзывы:

Нет отзывов