RBH Access Technologies Integra32 Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 64

RBH Access Technologies Integra32 Скачать руководство пользователя страница 10

Chapter 2
Intelligent Field Panel

Integra32

™

Hardware Guide

RBH Access Technologies Inc.

6

Off

Off

On

On

Off

12

On

Off

On

On

Off

13

Off

On

On

On

Off

14

On

On

On

On

Off

15

Off

Off

Off

Off

On

16

Direct Connect/Modem Selection

DIP switch 8 specifies whether the IRC-2000 is connected directly to a serial port on the
PC or communicates with the PC over a modem. Contact the RBH tech support office
for information on the optional TCP/IP Ethernet connection.

Direct Connect / Modem Selection

DIP Switch 8

Interface Type

OFF

Direct Connect To PC

ON

Modem

DIP  switch  8  specifically  turns  on  the  password  requirement  and  enables  modem  call-
back.    The  panel  will  still  answer  a  modem  call  with  DIP  switch  8  off.    You  should
initially  set  up  the  panel  with  DIP  switch  8  off,  program  the  panel  and  download to it.
Then turn DIP switch 8 on to enable password checking.

Computer/Modem Port Baud Rate Selection

The controller's serial port baud rate is set with controller DIP switches 6 and 7. This
setting determines the speed used to communicate with the modem or PC serial port. If
the controller is connected directly to the PC, the controller baud rate must be the same
as the baud rate set for the port on the PC. The default PC baud rate is 38,400.

Controller Baud Rate Selection

DIP Switch 6

DIP Switch 7

Baud Rate

OFF

OFF

9,600

ON

OFF

28,800

OFF

ON

38,400

ON

ON

56,000

«
...
8
9
10
11
12
...
»

Содержание Integra32

































































Отзывы:

Нет отзывов