background image

9

www.raytecled.com

UK / Europe Tel: +44 (0) 1670 520055
Americas Tel:  +1 613 270 9990

3. Maintenance

1.  It is essential that all SPARTAN Bulkhead units are maintained in accordance with 

the requirements of the EN60079-17 standard: (Electrical apparatus for explosive gas 

atmospheres – other than mines).

2. 

IMPORTANT

.    No  modifications  are  permitted  to  the  unit,  all  spare  parts  must  be 

purchased  from  the  manufacturer,  unauthorized  modifications  or  spare  parts  will 

invalidate certification and make the equipment dangerous.

3.  Isolate the SPARTAN Bulkhead from the mains supply and allow to cool before 

carrying out any maintenance work.

•  For Emergency variants, battery must be isolated/ connected when a hazardous 

environment is NOT present prior to carrying out any maintenance work.

4.  In the unlikely event of a number of LED’s failing, the light engine assembly must be 

replaced. This is achieved by loosening front cover bolts, disconnecting the white 

LED cables to power supply, remove four M6 bolts from rear of light engine and pull 

the  light  engine  assembly  clear.  Re  fitting  a  light  engine  is  a  reversal  of  the  above 

procedure.

5.  The unit has one independent power supply, in the event that the power supply 

needs to be replaced the cables to the LED and mains terminal block will need to 

be disconnected, the four M6 bolts released, then the power supply can then be 

removed. Fitting a new power supply is a reversal of the above procedure. 

6.  Disposal of packaging, SPARTAN unit and old LED assemblies should be carried out 

in accordance with national regulations.

PROTECTION/CERTIFICATION

CML13ATEX3007, IEC Ex CML14.0001 & CML21UKEX3099

II 2 GD Ex eb mb IIC T4 Gb

Ta -52°C to +55°C (standard variants)

II 2 GD Ex eb mb IIC T4 Gb

Ta -20°C to +46°C (emergency variants)

Ex tb IIIC T98°C Db

IP66 & IP67 Ta = -52°C to +55°C

110V-254V AC or 18-48V AC/18-69V DC

CML 17ATEX4231, IEC Ex CML17.0135 & CML21UKEX4106

II 3 GD Ex ec mc IIC T4 Gc

Ta -50°C to +55°C (standard variants)

II 3 GD Ex ec mc IIC T4 Gc

Ta -20°C to +55°C (emergency variants)

Ex tc IIIC T98°C Dc

IP66 & IP67 Ta = -50°C to +55°C

110V-254V AC or 18-48V AC/18-69V DC

Содержание BL24-EM















Отзывы: