Raypak TempTracker mod+ Скачать руководство пользователя страница 32

Страница: 32 / 32

specIfIcatIons

Voltage Input:

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120 VAC 60 Hz

Power Consumption:

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 VA Max

Operating Temperature:

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

F to 120

Operating Humidity:

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20% to 80% non-condensing

Dimensions:

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

11"W x 9" H x 3 ¾" D

Weight:

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.5 pounds

TempTracker mod+ Specifications

Lead Stage Rotation:

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Time ( 1 to 1440 Hours (60 days)), Manual, Last-On

Pump Output:

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (1) N.O. S.P.S.T

Boiler Modes:

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Auto, Manual, Standby, On, Off

Standby Time:

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 to 60 minutes

Modulating Output Types:

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (4) 4-20mA, 0-5V, 0-10V, 1-5V, 2-10V

Output Relay Ratings:

. . . . . . . . . . . . . (5) 1 Amp inductive, 6Amp resistive at 120 VAC 60 Hz, 15A total for all circuits

Add-On TempTracker mod+ Extension Panels:

. . . . . . . . . . up to two TempTracker mod+ Extension Panels using RS485

Ignition Point %:

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ---

Modulation Start Point %:

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45%

Modulation Mode:

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Parallel

Temperature Display:

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Fahrenheit or Celsius.

Display:

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Graphical Alphanumeric (7 rows x 21 char. each)

LED:

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (1) System Output relay, (4) Boiler Output relays

Sensor Ranges:

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Outdoor temperature sensor - minus 35

F to 250

Heating system sensor - minus 35

F to 250

Outdoor Cutoff Range:

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

F to 100

F, ON and OFF

Reset Ratio Range:

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (1.00 : 4.00) to (4.00 : 1.00) (Outdoor : System Water)

Offset Adjustment:

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .minus -40°F to plus 40°F

Minimum Water Temperature:

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70

F to 170

Maximum Water Temperature:

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90

F to 240

Set Point Temperature Range:

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70

F to 250

EMS Temperature Range:

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70

F to 240

Domestic Hot Water:

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . with Priority or without Priority

Pump Run-On:

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 to 360 minutes

Purge Delay:

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.0 to 10.0 minutes

Lag Delay:

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0 to 60 minutes

Last Stage Hold:

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0 to 30°F

Schedules:

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (1) Day and (1) Night (Setback) settings per day

Night Setback:

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0°F to 75°F

Power Backup:

. . . . . . . . . Lithium coin battery, 100 days minimum 5 year replacement (Maintains Clock in power outages).

External Inputs:

. . . . . . . . . .TStat Input/Shutdown Input/Setback Input, and Prove Input/DHW Input (Dry Contacts Only)

Season:

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Winter and Summer.

TempTracker mod+ Extension Specifications

(Each TempTracker mod+ Extension can add up to (6) additional modulating boilers. A maximum of two TempTracker mod+
Extensions can be added to a single TempTracker mod+.)

Extension Numbering:

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Toggle Switch A or B

Boiler Outputs:

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (6) N.O. S.P.S.T.

Modulating Output Types:

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (6) 4-20mA, 0-5V, 0-10V, 1-5V, 2-10V

Output Relay Ratings:

. . . . . . . . . . . . . . . . 1 Amp inductive, 6Amp resistive at 120 VAC 60 Hz, 15A total for all circuits

Connection to TempTracker mod+ and another extension:

Two RS485 connections using 6 wire phone cable (Cable is provided)

059042-00D

Raypak, Inc.

2151 Eastman Ave.,

Oxnard, CA 93030

PH: (805) 278-5300

FAX: (805) 278-5468

Содержание TempTracker mod+

































Результаты поиска

Содержание TempTracker mod+

Отзывы:

Похожие инструкции для TempTracker mod+

Бренды по названию

Популярные бренды

Raypak TempTracker mod+, Инструкция по установке и эксплуатации

Результаты поиска

Содержание TempTracker mod+

Отзывы:

Похожие инструкции для TempTracker mod+

Бренды по названию

Популярные бренды