Raypak TempTracker mod+ Скачать руководство пользователя страница 7

Страница: 7 / 32

TempTracker mod+ & TempTracker mod+ Extension Installation Manual

system run-on

• This feature lets the TempTracker mod+ run the SYS relay for a longer period after the boilers have been turned off. When this relay

is used to control a pump, it helps in dissipating the excess heat from the boilers combustion chamber.

InstallatIon

Each of the TempTracker mod+ or TempTracker mod+ Extension consists of three primary enclosure components.

• The Enclosure Display Module:

contains the display, buttons, LEDs and electric wiring terminals. It has two screws to hold it to

the base. A program configuration switch, used to adjust TempTracker mod+ settings, is placed above the terminals. This switch

is enclosed with the enclosure wiring cover for security. Wiring terminals are of the plug-in type to ease installation and removal.

• The Enclosure Base:

contains the holes to mount and hold the control against the wall or any flat surface. All other enclosure

components mount on the base. The bottom section of the Enclosure Base contains the wiring chamber with knockouts on the
bottom to easy installation.

• The Enclosure Wiring Cover:

seals the wires from the external environment. It has two screws to hold it the base and a hole to

secure a lock on the wiring enclosure. A plastic web that separates the wiring chamber into high and low volt sections has been
provided.

MountInG tHe enclosure

• Select a location near the equipment to be controlled.

• The surface should be flat, and be sufficiently wide and strong to hold the

TempTracker mod+ or the TempTracker mod+ Extension.

• Keep the control away from extreme heat, cold, or humidity. Ambient

control operating temperature is from 20 to 120°F.

• Remove the Enclosure Wiring Cover from the control enclosure by

removing the two bottom screws.

• Remove the Enclosure Display Module by removing the middle screws.

• Screw the Enclosure Base to the surface through the upper and lower

mounting holes on the back of the enclosure.

• Replace the Enclosure Display Module and replace the middle screws.

• Do not replace the enclosure wiring cover until all wiring is done.

Mounting Holes

Display Mounting Screws

Wiring Cover

Mounting Screws

Enclosure Display Module

Enclosure Wiring Cover

Enclosure Base

Hole for optional lock

(not supplied)

Содержание TempTracker mod+

































Результаты поиска

Содержание TempTracker mod+

Отзывы:

Похожие инструкции для TempTracker mod+

Бренды по названию

Популярные бренды

Raypak TempTracker mod+, Инструкция по установке и эксплуатации

Результаты поиска

Содержание TempTracker mod+

Отзывы:

Похожие инструкции для TempTracker mod+

Бренды по названию

Популярные бренды