Raypak TempTracker mod+ Hybrid Скачать руководство пользователя страница 42

Страница: 42 / 56

Raypak, Inc.

HTC# 059105-00D

copy settings - Boiler a only

(Modulating Boilers Only)

Button:

STAGE/Copy Settings

• If all the active modulating boilers are to be set to the same Ignition % and Modulation %,

they can be set for Boiler A and then copied to the other modulating boilers.

• It is still required to select the Mode for all other boilers as the Mode is NOT copied.

note

The Mode MUST be set for each boiler. The Copy Settings command will not set the

Mode for the remaining boilers. Only Ignition % and Modulation Start % are copied.

-- COPY SETTINGS --

From Stage A to

all other stages

BACK COPY

trouBlesHootInG

sensor Inputs

display shows sensor open or sHort

When the display shows sensor OPEN, short the control sensor input terminals. The display should change to read SHORT. This

indicates that the sensor wires are not continuous. If the display does not SHORT, the TempTracker mod+ Hybrid may be damaged.

When the display shows sensor SHORT, remove the wires from the sensor terminals. The display should change to read OPEN. In

this case, replace the sensor. Otherwise, if the display does not show OPEN, the TempTracker mod+ Hybrid may be damaged.

display shows an Incorrect temperature

Remove the wires from the sensor terminals. The display should change to read OPEN. If it does not, the

TempTracker mod+ Hybrid may be damaged. Take an ohm reading across the detached sensor wires. The ohm reading should

correspond to the Temperature Sensor Chart. If it does not, the sensor may be damaged.

control operatIon

no Heat

• Season

- Make sure that the Season is set to Winter. See "Season" on page 31 and "Display Messages" on page 40.

• Prove

- Even though, the system relay may be energized, the TempTracker mod+ Hybrid will not energize and stage relays unless

the Prove is shorted. See "Display Messages" on page 40 and "W iring the Prove" on page 13.

• Shutdown

- The TempTracker mod+ Hybrid will deactivate stage outputs when the Shutdown terminals are shorted. See "Display

Messages" on page 40 and "W iring the Shutdown, Tstat, or Setback" on page 12.

• Tstat

- The TempTracker mod+ Hybrid will deactivate stage outputs when the Tstat terminals are open. See "Display Messages" on

page 40 and "W iring the Shutdown, Tstat, or Setback" on page 12.

• Sensor Fault

- When the Sensor Fault is set to All Off in the startup menu, the System sensor fault (in all Sensor Type modes) or

the Outdoor sensor fault (in Reset mode) will de-energize all stage relays. See "Display Messages" on page 40 and "Sensor Fault" on

page 26.

• System or Outdoor Sensor

- If the System or Outdoor sensor reading was higher that the actual temperature, the

TempTracker mod+ Hybrid might not bring any stage on. Check "Display shows an Incorrect Temperature" section.

• Outdoor Cutoff

- If the Outdoor cutoff was set too low, the building might be allowed to cool more than is desired. A comfortable

setting is between 60°F to 65°F. "Outdoor Cutoff Temperature" on page 32

too Much Heat

• Indirect Domestic Hot Water call

- The TempTracker mod+ Hybrid will raise the temperature of the system to the DHW Set Point

on a DHW call, connected to terminals 29 and 30. Check to see if there is a call for DHW and the length of time it lasts.

• Reset Ratio and Offset

- If excessive heat occurs only in certain weather conditions, adjust the Reset Ratio and Offset. See

"Outdoor Reset Concept" on page 5. If excessive heat occurs year round, reduce the Offset.

• Boiler Mode Settings

- The TempTracker mod+ Hybrid will only controls boilers their mode is set to Auto or Standby. Check if

any boiler stage is set to Manual or On. See "Mode" on page 41.

• Control Settings

- The Last Stage Hold will allow only the Lead boiler to stay on for an additional number of degrees. If the setting

is too high, and only the Lead boiler is on, the system can over heat. Reduce the Last Stage Hold setting. See"Last Stage Hold" on

page 34.

Содержание TempTracker mod+ Hybrid

























































Результаты поиска

Содержание TempTracker mod+ Hybrid

Отзывы:

Бренды по названию

Популярные бренды

Raypak TempTracker mod+ Hybrid, Инструкция по установке и эксплуатации

Результаты поиска

Содержание TempTracker mod+ Hybrid

Отзывы:

Бренды по названию

Популярные бренды