Raypak TempTracker mod+ Hybrid Скачать руководство пользователя страница 26

Страница: 26 / 56

Raypak, Inc.

HTC# 059105-00D

Indirect domestic Hot Water set point

(Available with any of the DHW Priority options)

Adjustable from 140°F/60°C to 200°F/93°C

Default: 180°F/82°C

Button:

MENU/<System Startup>/..../Prove-Setpoint

• On a DHW call, the TempTracker mod+ Hybrid will raise the target temperature to the

DHW Set Point until the DHW call expires.

- DHW SETPOINT -

180

[

]

BACK

▲

▼

SAVE

shutdown/tstat/setback Mode

Shutdown Input, Tstate Input, Setback Input

Default: Shutdown Input

Button:

MENU/<System Startup>/..../Setback\Shutdown

• This menu determines the functionality of terminals

31 and 32

• The TempTracker mod+ Hybrid has two levels of heat, a Normal/Day and a Setback/Night.

The Normal/Day is good for when buildings are occupied and people are active. The

Setback/Night holds a lower system temperature for night periods or when buildings are

unoccupied.

- SETBCK/SHUTDOWN -

Shutdown/Disable

Tstat/Enable

Setback

BACK

▲

▼

SAVE

• When Shutdown or Tstat is selected, the Day/Night Schedules will be available in the

operating menu. See next settings. Terminals

31 and 32

will function as a Shutdown (Turn

off boilers when shorted) or as a Tstat (Turn off boilers when opened). However, a call for

indirect DHW will bring the boilers on.

• When Setback is selected, the External Signal option will switch the

TempTracker mod+ Hybrid to Setback mode when terminals

31 and 32

are shorted. This

allows an external device or control to provide the setback signal. No scheduling or boost

menu options will be available with Setback.

Boost Mode

(Not Available in Setback Mode)

30 Minutes, Disabled

Default: Disable

Button:

MENU/<System Startup>/..../Boost Mode

• The morning Boost is designed to return the building to comfortable ambient temperatures

after the cooler Night (Setback) period. The control will accomplish this by running

elevated water temperatures (will add Setback setting to calculated water temperature) for

30 minutes before the start of the Day schedule setting. That is, if the normal day set point

at a specific outdoor was 145˚F and the Setback setting was 20˚F, the boost will raise the

system calculated temperature to 165˚F for 30 minutes before the start of the Day Schedule

setting.

• If no Boost is needed, then simply select Disabled from the Boost Menu.

• Boost is only available if Shutdown or Tstat is selected as an option. See previous setting.

--- BOOST MODE ---

30 Minutes

Disable

BACK

▲

▼

SAVE

sensor Fault

All Off, All On

Default: All On

Button:

MENU/<System Startup>/..../Sensor Fault

• The Sensor Fault will determine the operating status of all output stages that has their Mode

set to Auto when a sensor reads Short or Open.

• When All-Off is selected, the control will turn all boilers Off when the System sensor reads

Short or Open. However, when the Outdoor sensor reads Short or Open, the control will try

to maintain the Minimum Water Temperature.

• When All-On is selected and the Boiler Type was set to other than Hybrid, the control will

turn all boilers On to a 100% when the System sensor reads Short or Open and the outdoor

temperature is below Outdoor Cutoff. However, when the Outdoor sensor reads Short or

Open, the control will try to maintain the Maximum Water Temperature.

• When All-On is selected and the Boiler Type was set to Hybrid, the control will turn all

Non-Condensing boilers On to full fire when the System sensor reads Short or Open and the

outdoor temperature is below Outdoor Cutoff. During that time all Condensing boilers will

turn Off. When the Outdoor sensor reads Short or Open, the control will try to maintain the

Maximum Water Temperature.

--- SENSOR FAULT ---

All Off

All On

BACK

▲

▼

SAVE

note

A good practice after performing

any Startup menu modification

is to check all operating settings

and adjustments to match the

new settings.

Содержание TempTracker mod+ Hybrid

























































Результаты поиска

Содержание TempTracker mod+ Hybrid

Отзывы:

Бренды по названию

Популярные бренды

Raypak TempTracker mod+ Hybrid, Инструкция по установке и эксплуатации

Результаты поиска

Содержание TempTracker mod+ Hybrid

Отзывы:

Бренды по названию

Популярные бренды