Raypak TempTracker mod+ Hybrid Скачать руководство пользователя страница 5

Страница: 5 / 56

TempTracker mod+ Hybrid Installation and Operation Manual

HTC# 059105-00D

outdoor reset concept

The TempTracker mod+ Hybrid has multiple operating modes that satisfy most

hydronic systems. It changes the System Set Point based on outdoor temperature

(Outdoor Reset). The TempTracker mod+ Hybrid varies the temperature of the

circulating heating water in response to changes in the outdoor temperature. The

heating water temperature is controlled through the modulation or sequencing of the

stages.

The TempTracker mod+ Hybrid also controls the system circulating pump with an

adjustable Outdoor Cutoff. When the outdoor temperature is above the Outdoor

Cutoff, the pump is off and no heating water is circulated through the system. When

the outdoor temperature drops below the Outdoor Cutoff, the system pump relay is

activated and the heating water circulates through the system. The temperature of

the heating water is controlled by the Reset Ratio, Water Offset, and changes with

Outdoor temperature.

reset ratio/outdoor reset

When a building is being heated, heat escapes through the walls, doors, and windows

to the colder outside air. The colder the outside temperature, the more heat escapes.

If you can input heat into the building at the same rate that it is lost out of the

building, then the building temperatures will remain constant. The Reset Ratio is an

adjustment that lets you achieve this equilibrium between heat input and heat loss.

The starting point for most systems is the 1.00 (OD):1.00 (SYS) (Outdoor

Temperature : Heating Water Temperature) ratio. This means that for every degree

the outdoor temperature drops, the temperature of the heating water will increase

one degree. The starting point of the curves is adjustable, but comes factory selected

at 70

F Outdoor Temperature and 100

F Water Temperature. For example with

a 1.00 (OD):1.00 (SYS) ratio, if the outdoor temperature is 50

F, this means the

temperature has fallen 20

from the starting point of 70

F. Therefore, the heating

water temperature will increase 20

to 120

Each building has different heat loss characteristics. A very well insulated building

will not lose much heat to the outside air, and may need a Reset Ratio of 2.00

(OD):1.00 (SYS) (Outdoor:Water). This means the outdoor temperature would have

to drop 2 degrees to increase the water temperature 1 degree. On the other hand, a

poorly insulated building with insufficient radiation may need a Reset Ratio of 1.00

(OD):2.00 (SYS). This means that for each degree the outdoor temperature dropped

the water temperature will increase 2 degrees. The TempTracker mod+ Hybrid has a

full range of Reset Ratios to match any buildings heat loss characteristics.

A heating curve that relies not only on Outdoor temperature but also on the type of

radiation will improve heat comfort. The following are suggested initial settings for

different types of radiation based on average building insulation and heat loss. The

contractor can fine tune these adjustments based on the specific building need.

type of radiation in Building

reset ratio

offset

Radiators (Steel & Cast Iron)

1.00 (OD) : 1.00 (SYS)

0˚F

Baseboard (Finned copper tube& Cast Iron)

1.00 (OD) : 1.00 (SYS)

0˚F

Radiant (High Mass/Concrete)

4.00 (OD) : 1.00 (SYS)

-10˚F

Radiant (Low Mass/Joists)

2.00 (OD) : 1.00 (SYS)

-10˚F

Fan Coils & Air Handlers

1.00 (OD) : 1.00 (SYS)

20˚F

Outdoor Temperature

130

120

110

100

Outdoor Temperature

110

100

Outdoor Temperature

150

140

130

120

1:4

With a 0° Offset, the
Reset curves begin at
100° Water Temperature.

With a -20° Offset, the
Reset curves begin at
80° Water Temperature.

With a +20° Offset, the
Reset curves begin at
120° Water Temperature.

1:4

1:1

4:1

100

+20 Offset

-20 Offset

Outdoor Temperature

130

120

110

100

1:4

1:1

4:1

Colder

Warmer

Outdoor Temperature (in °F)

-10

-20

100

120

110

130

140

150

160

180

170

190

200

210

220

1:3

1:2

1:1.5

1:1.25

1:1

1.25:1

1.5:1

2:1

3:1

4:1

°F

)

Reset Ratio Curves

Reset Ratio is Presented as

Outdoor Temp. : Water Temp. Ratio

1:4

Содержание TempTracker mod+ Hybrid

























































Результаты поиска

Содержание TempTracker mod+ Hybrid

Отзывы:

Бренды по названию

Популярные бренды

Raypak TempTracker mod+ Hybrid, Инструкция по установке и эксплуатации

Результаты поиска

Содержание TempTracker mod+ Hybrid

Отзывы:

Бренды по названию

Популярные бренды