Raypak TempTracker mod+ Hybrid Скачать руководство пользователя страница 40

Страница: 40 / 56

Raypak, Inc.

HTC# 059105-00D

dIsplaY MessaGes

The TempTracker mod+ Hybrid display layout reserved the second line for message indications. The following is a list of the most

common Message Display Line information:

• Boost To 170˚F

The Boost has started 30 minutes before the Day Schedule setting and the Boost temperature is 170˚F.

See "Boost Mode" on page 26.

• DHW Call (180˚F)

There is an indirect DHW call. The TempTracker mod+ Hybrid will raise the system Set Point to the

indicated temperature. DHW increases calculated temperature to the DHW Set Point. See "Indirect

Domestic Hot Water Set Point" on page 26.

• Holding Until 150˚F

The Lead boiler is in Last Stage Hold. This example shows that the lead stage will turn off when system

temperature reaches 150˚F. See "Last Stage Hold" on page 34.

• Interface Module Error There is no communication to the BACnet Module Interface while the BACnet Mode is set to Enable.

See "BACnet Mode" on page 27.

• Lag Delay: 123

The lead boiler is at 100% and the remaining purge time to start the lag boiler in seconds is 123. See "Lag

Delay" on page 35.

• Outdoor Cutoff

The outdoor temperature is above the Outdoor Cutoff setting. No boilers will be active for heating. See

"Outdoor Cutoff Temperature" on page 32.

• Prove Failure

After boilers have run for some time, Prove signal has ended. All boilers set to Auto or Standby will

de-energize. However, the System relay will remain energized. See "Prove/Indirect Domestic Hot Water

(DHW) Priority" on page 25 and "W iring the Prove" on page 13.

• Purge Delay: 23

A boiler is in purge cycle and the remaining purge time in seconds is 23. See "Purge Delay" on page 33.

• Setback to: 130˚F

The Night Schedule or Setback input is active. Current Setback temperature is 130˚F. See "Setback"

on page 33. See "Day/Night Schedules" on page 37.

• Shutdown Active

The Shutdown Terminals are Shorted. No boilers will be active. See "Shutdown/Tstat/Setback Mode" on

page 26. Also See "Wiring the Shutdown, Tstat, or Setback" on page 12.

• Summer

The control is set to Summer. No heat is active. See "Season" on page 31.

• Switch in: 00:30

The switch from one group to the other will take place after 30 minutes. See "Switch Delay" on page 22.

• System Run-On: 46

The System relay is ON for the System Run-On Delay. This example shows that it will remain in System

Run-On for an additional 46 seconds before turning off. See "System Run-On" on page 33.

• Tstat Call

The Tstat Terminals are Shorted. Boilers will be active. See "Shutdown/Tstat/Setback Mode" on page 26.

• Waiting for Prove

The System relay is ON and the prove terminals are open before the lead boiler relay can energize. See

"Prove/Indirect Domestic Hot Water (DHW) Priority" on page 25.

BoIler staGe settInGs

Button:

STAGE/

The Stage menu provides adjustment for each of the individually boiler operations.

• In most installations, all active boiler adjustments are the same, but each can be configured

differently if desired.

• If the boilers are not set up properly, the TempTracker mod+ Hybrid operation may appear

to be erratic.

• When the

STAGE

button is depressed, the Boiler A settings menu will be shown.

• Make all the appropriate settings for Boiler A (See below).

• After completing all the settings for Boiler A (See below), you have the option of copying

these settings to all other modulating boilers. Everything but the Mode -- Auto/Standby/

Manual/Off/On -- will be copied.

• Then select the

option from the menu to reach the Boiler B settings

menu. Continue until all boilers have been set.

• If an Extension is connected to the TempTracker mod+ Hybrid and the stages have been set

through the Startup menu, then scrolling through stages using the

and

menu options will scroll through the Extension stages as well.

note

To change the TempTracker mod+ Hybrid settings, the Program/Run Switch must

be set to Program. The switch is located under the Enclosure Wiring Cover for

security. The Enclosure Wiring Cover can be secured using a lock.

Modulating Boiler Stage Menu

STAGE A SETTINGS

Mode

Auto

Ignition %

Mod Start %

80%

Copy Settings

BACK

▲

▼

SELECT

Sequencing Boiler Stage Menu

STAGE A SETTINGS

Mode

Auto

BACK

▲

▼

SELECT

SYSTEM

A
B
C
D

1 2

RUN

PROGRAM

DO NOT APPLY ANY VOLTAGE

TO INPUT TERMINALS

3 4 5 6 7 8 9 10 11 12

30 31

L N

RS-485

GND

VLT

SYS

PWR

CUR / VLT

GND

VLT

GND

VLT

GND

VLT

TEMP

OUTDOOR

TEMP

SYSTEM

EXTENSION

MODULE

CUR / VLT

PROVE

/DHW

SHUTDOWN

/SETBACK

FOR ALL CIRCUITS

120VAC, 6A RESISTIVE

OUTPUT RATINGS:

1A PILOT DUTY, 15A TOTAL

115VAC 60Hz , 30VA MAX

INPUT RATINGS:

USE COPPER WIRE,

CLASS 1 WIRE ONLY.

CAUTION

: RISK OF ELECTRIC SHOCK

More than one disconnect switch may be required

to de-energize the equipment before servicing.

ENCLOSED

ENERGY

MANAGEMENT

EQUIPMENT

99RA

/TSTAT

HYBRID

Содержание TempTracker mod+ Hybrid

























































Результаты поиска

Содержание TempTracker mod+ Hybrid

Отзывы:

Бренды по названию

Популярные бренды

Raypak TempTracker mod+ Hybrid, Инструкция по установке и эксплуатации

Результаты поиска

Содержание TempTracker mod+ Hybrid

Отзывы:

Бренды по названию

Популярные бренды