Raypak MVB 1104A Скачать руководство пользователя страница 24

Страница: 24 / 64

Fig. 23: Wiring Location

Fig. 24: Locator Dimples for Optional Components

Fig. 25: Low Voltage Field Wiring

closure (including a remote thermostat) across these

terminals will enable the MVB unit to run. Caution

should be used to ensure neither of the terminals

becomes connected to ground.

Wiring the Outdoor Sensor

1. There is no connection required if an outdoor sen-

sor is not used in this installation.

2. If using an Outdoor Sensor (option B-32), connect

the sensor wires to the terminals marked OUT-

DOOR SENSOR (see Fig. 25). Caution should be

used to ensure neither of these terminals

becomes connected to ground.

3. Use a minimum 18 AWG wire for runs of up to 150

feet.

4. Mount the outdoor sensor on an exterior surface of

the building, preferably on the north side in an

area that will not be affected by direct sunlight and

that will be exposed to varying weather conditions.

NOTE:

A grounding electrode conductor shall be

used to connect the equipment grounding

conductors, the equipment enclosures, and the

grounded service conductor to the grounding

electrode.

Field Wiring Connection

CAUTION:

Label all wires prior to disconnection

when servicing controls. Wiring errors can cause im-

proper and dangerous operation. Verify proper

operation after servicing.

DANGER: SHOCK HAZARD

Make sure electrical power to the heater is discon-

nected to avoid potential serious injury or damage to

components.

Wiring the Enable/Disable

Connect the Enable/Disable wiring to the field wiring

terminal (shown in Fig. 25). Alternately, any dry contact

Содержание MVB 1104A

































































Результаты поиска

Содержание MVB 1104A

Отзывы:

Похожие инструкции для MVB 1104A

Бренды по названию

Популярные бренды

Raypak MVB 1104A, Инструкция по установке и эксплуатации

Результаты поиска

Содержание MVB 1104A

Отзывы:

Похожие инструкции для MVB 1104A

Бренды по названию

Популярные бренды