Raymarine Transducers Скачать руководство пользователя страница 51 | Manualshive

Страница: 51 / 56

Raymarine Transducers Скачать руководство пользователя страница 51

Chapter 3: Maintenance

45

How to Contact Raymarine

On the Internet

Visit the Raymarine World Wide Web site for the latest information
on Raymarine electronic equipment and systems at:

www.raymarine.com

Customer Support

Navigate to the Customer Support page for links to:

•

Finding Factory Service locations and Authorized Dealers near
you

•

Registering your Raymarine products

•

Accessing handbooks in Adobe Acrobat format

•

Downloading RayTech software updates

•

Accessing the Raymarine solution database

Clicking the Find Answers link routes you to our solution database.
Search questions and answers by product, category, keywords, or
phrases. If the answer you are seeking is not available, click the Ask
Raymarine tab to submit your own question to our technical support
staff, who reply to you by e-mail.

In the US

Accessories and Parts

Many Raymarine accessory items and parts can be obtained directly
from your authorized Raymarine dealer. However, if you are in need
of an item not available from the retailer, please contact Raymarine
Technical Services at:

800-539-5539 ext. 2333, or
603-881-5200.

Technical Service is available Monday through Friday 4:00 AM to
6:00 PM Eastern Time.

Please have the Raymarine item or part number ready when calling if
placing an order. If you are not sure which item is appropriate for your
unit, you should first contact the Technical Support Department to
verify your requirements.

«
...
49
50
51
52
53
...
»

Содержание Transducers

























































Отзывы:

Нет отзывов