Raymarine Transducers Скачать руководство пользователя страница 21 | Manualshive

Страница: 21 / 56

Raymarine Transducers Скачать руководство пользователя страница 21

Chapter 2: Installation

15

Chapter 2: Installation

This chapter gives details on how to install your

transducer.

Instructions are divided into the following sections:

•

Transom Mount Transducers - recommended for personal
watercraft and powerboats with outboard, inboard-outboard and
jet drives.

•

Thru-Hull Transducers - recommended for boats with straight-
shaft inboard engines.

•

In-Hull transducers- recommended for fiberglass hulls, espe-
cially in high speed power boats and racing sailboats.

2.1 Installing the Transom Mount Transducer

Preparation

Transducer Mounting Bracket

When installed, the lower surface of the transducer should tilt down
toward the rear at a slight angle (2° to 5°). The mounting bracket
includes a wedge; depending on the angle of the transom on your
boat, you may need to install this wedge to get the correct transducer
angle.

1. To attach the transducer to the bracket, insert the transducer

mounting lugs into the slot in the bracket as shown in Figure 2-1 .

Figure 2-1:

Fitting the Transducer to the Bracket

Correct

Incorrect

Lower the transducer and

snap in the release clip

Attach the two parts

Bracket is installed

upside down

D4874-2

«
...
19
20
21
22
23
...
»

Содержание Transducers

























































Отзывы:

Нет отзывов