background image

Chapter 1: Introduction

Safety notices

Warning: Product installation and
operation

This product must be installed and operated in
accordance with the instructions provided. Failure to
do so could result in personal injury, damage to your
boat and/or poor product performance.

Caution: Power supply protection

When installing this product ensure the power source
is adequately protected by means of a suitably-rated
fuse or automatic circuit breaker.

Caution: Use correct lifting point

When lifting the antenna unit, always lift from the base
plate. Do NOT use the antenna cover or damage to
the cover could occur.

Caution: Do not damage connectors

Take care to avoid damage to the connectors
underneath the antenna base plate when moving the
unit. Do NOT use these connectors to lift the unit.

Caution: Remove transit packing

Before installing or operating the product, open the
antenna unit cover and remove the foam transit
packing inserts from the unit base.

Caution: Antenna coating

Do NOT paint or apply any other finish to the antenna
unit. This could degrade performance beyond
acceptable limits.

Important information

Handbook information

Your STV system provides television access to hundreds of TV
channels. On the open sea or at the dock, the Raymarine Satellite
TV system automatically identifies, acquires and tracks compatible
signals from all digital video broadcast (DVB) satellites.

This handbook describes how to install, connect and maintain the
Raymarine Satellite Television (STV) system . It is used with the
following models:

Introduction

7

Содержание 37STV Gen2





















Отзывы: