Raycus RFL-P500 Скачать руководство пользователя страница 27

Страница: 27 / 27

Wuhan Raycus Fiber Laser Technologies Co., Ltd.

User Guide of RFL-P500

fault operating is not warranted. Accessories and fiber connectors are excluded

from this warranty.

According to the warranty, client should write to us within 31days after the

defect is discovered. This warranty does not involve any other party, including

specified buyer, end-user or customer and any parts, equipment or other products

produced by other companies.

WARNING

: It is the customer’s responsibility to understand and follow

operating instructions in this UserGuide and specifications prior to
operation-failure to do so may void this warranty.Accessories and fiber
connectors are not covered by this warranty.

7.3

Service and Repair



Do not open the device. There are no user serviceable parts, equipment

orassemblies for user in this product. All service and maintenance shall be

performedby qualified Raycus personnel.



Please contact Raycus as soon as possible when problems under warranty about

maintenance happened to the product.



The product returned with permission should be placed in a suitable container.



If any damage happened to the product, please notify the carrier in document

immediately.

We reserve the right to make changes in design or constructions of any of

our products at anytime without incurring any obligation to make changes or

install the same on units previouslypurchased.

All the items about warranty and service above provided by Raycus are

for uses’reference; formal contents about warranty and service are subject to

the contract.

Содержание RFL-P500




























Результаты поиска

Содержание RFL-P500

Отзывы:

Raycus RFL-P500, Руководство пользователя, Страница: 27 / 27

Результаты поиска

Содержание RFL-P500

Отзывы: