Raychem nvent MI Series Скачать руководство пользователя

Страница: 26 / 66

Heating Cable Repair

22 | nVent.com

nVent.com | 23

Continue heating conductor with the oxy-acetylene

torch (this does not take much heat) and at the

same time touch brazing rod to the end of the

conductor and apply enough silver solder to tin

the end of the conductor. Repeat for remaining

conductors on both cables to be joined.

Hot-cold joint

: Using oxy-acetylene torch, apply heat

to the center of the cold lead conductor with a small

flame (see Appendix E) and touch or wipe brazing

rod onto the

face

of the conductor by turning the rod

between the fingers. This will ensure that the flux melts

off the rod and onto the conductor evenly. Take care

not to get any flux near the end of the cable where it

might contaminate the magnesium oxide powder.
Continue heating cold lead conductor with the

oxy-acetylene torch (this does not take much heat)

and at the same time touch brazing rod to the face

of the conductor and apply enough silver solder

to form a small

bead

on the conductor face. If

repairing two conductor cable, repeat for remaining

cold lead conductor.

Figure 23: Cold lead conductor

Tin the conductors on the heated section using the

procedure above for hot-hot joint.

Note: If repairing a two conductor cable, bend

the two conductors of the heated section cable

into a 'Y' shape (see Figure 25) to accommodate

the distance apart of the cold lead conductors.

Cold lead

Bead

Содержание nvent MI Series



































































Результаты поиска

Содержание nvent MI Series

Отзывы:

Похожие инструкции для nvent MI Series

Бренды по названию

Популярные бренды

Raychem nvent MI Series, Руководство пользователя

Результаты поиска

Содержание nvent MI Series

Отзывы:

Похожие инструкции для nvent MI Series

Бренды по названию

Популярные бренды