Raychem nvent MI Series Скачать руководство пользователя

Страница: 56 / 66

Appendix D:

Drying Out Procedure

52 | nVent.com

nVent.com | 53

IMPORTANT: Wear full face shield when drying

out MI cable.

Damage to the cable sheath or a damaged or missing

joint or end cap will cause the magnesium oxide insulation

(white powder) to absorb moisture, resulting in low IR

readings. The cable must be “heated out" to remove the

moisture and bring the IR back to an acceptable level.

If moisture is detected in the cable, use the oxy-acetylene

torch with a large sizzling flame (Appendix E) and dry out the

cable beginning 12 in ( 30 cm) back from the joint or end cap

(heat cold lead first if making a hot-cold joint). If repairing

polymer jacketed heating cable and/or cold leads, begin 4 in

(10 cm) back from the joint or end cap to avoid melting the

polymer jacket. Alloy 825 sheath cable should be heated to a

dull red color and copper sheath cables should be heated to a

bluish-gray color.

Use a short sweeping motion of the torch and heat about

2 in (5 cm) of cable at a time, repeating 4 to 5 times. Move

the flame towards the joint or end cap as shown in Figure

D1. Do not sweep the flame in the opposite direction as this

will drive the moisture into the cable.

Figure 68: Use sweeping motion of torch

2 in (50 mm)

Repeat 4 to 5 times

Joint

Содержание nvent MI Series



































































Результаты поиска

Содержание nvent MI Series

Отзывы:

Похожие инструкции для nvent MI Series

Бренды по названию

Популярные бренды

Raychem nvent MI Series, Руководство пользователя

Результаты поиска

Содержание nvent MI Series

Отзывы:

Похожие инструкции для nvent MI Series

Бренды по названию

Популярные бренды