Raychem C910-485 Скачать руководство пользователя страница 42 | Manualshive

Страница: 42 / 54

Raychem C910-485 Скачать руководство пользователя страница 42

nVent.com | 42

C910-485 Communication Parameters
Parameter

Settings

Notes

Protocol

HTCBus (default)
Modbus RTU
Modbus ASCII

If you are communicating directly with the
controller using a different device, select the
MODBUS protocol.
For a detailed description of the controller’s
MODBUS mapping please refer to C910-485 Heat
Trace Controller.

Note:

HTCBus is for factory use only.

Modbus Addr

1 - 247

Set the communications address as desired. Each
controller on the serial communication bus must
have its own unique address.

Modbus Baud
Rate

Auto, 9600, 4800,
2400
1200, 600, 300.
Default =Auto

Select the data rate to be compatible with other
devices that will be connected to the controller for
communications Purposes. It is recommended
that the Setting be set to AUTO. The controller will
automatically select a BAUD RATE that is
compatible with the communications interface
installed.

Parity

NONE, EVEN, ODD Defines the type of parity bit to be used with

MODBUS communications.
Select the desired type of parity. Note that PARITY
can only be selected when using MODBUS
protocol.

Hardware

RS-485

Identifies the type of communications interface
installed in the C910-485.

Driver

Auto, RS-485, RS-
232, Modem.

Defines the way in which the controller’s program
communicates with the communications interface.

Profile

Auto, 3-wire RS232,
RS485, 1200 BAUD
Modem, 300 BAUD
Modem

Defines the way in which the controller’s program
supports communications handshaking and
communication interface signals.

Tx Delay

0.00 to 2.50
seconds

Allows a programmable delay between the receipt
of a communications message and the controller’s
reply. In some applications, it may be necessary to
delay the controller’s response to an inquiry for a
short period of time to allow external devices to
start up, stabilize and/or synchronize.

«
...
40
41
42
43
44
...
»

Содержание C910-485























































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды