manualshive.com logo in svg

Ravenheat CS 80 T, Инструкция по использованию, установке и обслуживанию

Ravenheat CS 80 T - высокоэффективный котел с возможностью установки и обслуживания. Инструкции по эксплуатации, установке и обслуживанию доступны для загрузки бесплатно на нашем сайте. Получите руководство по эксплуатации сейчас на manualshive.com.

Поделиться
Скачать
background image

    

  

18

 

 BS5546: Installation of gas hot water 

                           supplies  domestic purposes         

              (2nd Family Gases).
  

         BS5440: Flues (for gas appliances of rated

  

    input not exceeding 70 kW).

 
BS5440:  2 Ventilation (for gas appliances of

 

 

rated input not exceeding 70 kW).

BSEN 677: 1998 Gas fired central heating 
                  boilers.

             I.S. 813: Domestic gas Installations.
            
             The followings standards give valuable 

valuable 

             additional information:

             additional information:

             BS 7074: Expansion vessels and ancillary      

      

                            equipment 

                            equipment for sealed water system.
             BS 7593: Treatment of water in domestic hot 
                            water and central heating system.

             

Health & Safety Document No.635 

 The Electricity at Work Regulations, 1989.

 IMPORTANT: 
 

These appliances are CE certificated for 
safety and performance. It is therefore 
important that no external control devices e.g. 
flue dampers, economisers etc., are directly 
connected to this appliance unless covered 
by these Installation and Service Instructions 
or as otherwise recommended by  Ravenheat 
in writing. If in doubt please enquire.

 

Any direct connection of a control device 
not approved by Ravenheat could invalidate 
the certification and the normal appliance 
warranty. 

 

It could also infringe the Gas Safety regulations 
and the above regulations.

 NOTE:
 

The Ravenheat CS 80/90 (T) combi boiler has 
been tested and examined by CERTIGAZ, and 
is certified to comply with PrEN 483 and BS 
EN 625.

 

Manufacturers instructions must NOT be taken 
in any way as overriding statutory obligations.

 

If in doubt on any point please consult 
Ravenheat.

4

          

GENERAL REQUIREMENTS

4.1 SAFETY

 

 

Gas Safety (Installation and Use). 
Regulations.

   

It is law that all gas appliances are installed 
and serviced by a  Gas Safe registered installer 
in accordance with the above regulations and 
these installation instructions. All registered 
installers carry a Gas Safe I.D. card and have a 
registration number. Both should be recorded 
in your Benchmark commissioning checklist. 
You can check your installer on the Gas Safe 
register (www.gassaferegister.co.uk). Failure 
to install appliances correctly could lead to 
prosecution. It is in your own interest, and that 
of your safety, to ensure the law is complied 
with. Check the boiler and flue is the correct 
type for installation undertaken.

 

 

The  installation  of  the  boiler  MUST  be  in 

The installation of the boiler MUST be in 
accordance  with  the  latest  I.E.E.  (BS  7671) 

accordance with the latest I.E.E. (BS 7671) 
Wiring Regulations, local building regulations, 

Wiring Regulations, local building regulations, 
bye-laws of the local water authority, the 
building regulations and the Building Standards 
(Scotland) and any relevant requirements of 
the local authority.

4.2 GENERAL 

INFORMATION

   

Both  the  user  and  the  manufacturer  rely 

Both the user and the manufacturer rely 

            heavily on the installer, whose job it is 

            heavily on the installer, whose job it is 

to install the combination boiler and 

to install the combination boiler and 
connect it to a correctly designed heating 

connect it to a correctly designed heating 
system. Acquaint yourself with the relevan 

system. Acquaint yourself with the relevan 
British Standards concerning installation 

British Standards concerning installation 
requirements. If you need further advice on 

requirements. If you need further advice on 
any points contact the Technical Services 

any points contact the Technical Services 
Office on 0113 2527007 who would be 

Office on 0113 2527007 who would be 
pleased to help. It is recommended that tools 

pleased to help. It is recommended that tools 
suitable for brass fittings are used, and have 

suitable for brass fittings are used, and have 
a capability to accommodate hexagon sizes 

a capability to accommodate hexagon sizes 
up to 50 mm.

up to 50 mm.

 

 

APPLICABLE CODES OF PRACTICE

             Ref: Documents. 
 

 

 

 

Detailed recommendations are contained in the 
following British Standard Codes of Practice:

BS6891:2005:  Low pressure installation 

                        pipes.

BS6798: Installation of gas fired hot water 

 

 

boilers of rated input not exceeding  

  

70 

kW.

BSEN12828: Design for water based heating 
                    systems.

BSEN12831: Heating systems in buildings, 
                     Method for calculation of the 
                     design heat load.

BSEN14336: Installation & commissioning 
                     of water based heating 
                     systems. 

Содержание CS 80 T




































































Отзывы:

Нет отзывов

Похожие инструкции для CS 80 T

Ormandy Group Norland Technical Manual preview
Norland
Бренд: Ormandy Group Страницы: 18
ideal commercial HARRIER GTS 5 Installation And Servicing preview
HARRIER GTS 5
Бренд: ideal commercial Страницы: 36
A.O. Smith TC-099 Service Handbook preview
TC-099
Бренд: A.O. Smith Страницы: 74
NTI Trinity TX101 Installation And Operation Instructions Manual preview
Trinity TX101
Бренд: NTI Страницы: 84
Toastmaster TECC 4224 Installation Operation & Maintenance preview
TECC 4224
Бренд: Toastmaster Страницы: 13
Kenmore KWX-3V Owner'S Manual preview
KWX-3V
Бренд: Kenmore Страницы: 36
Kenmore 229.960021 Owner'S Manual preview
229.960021
Бренд: Kenmore Страницы: 24
Kenmore 3E W.65 Owner'S Manual preview
3E W.65
Бренд: Kenmore Страницы: 41
Kenmore K90-100 Installation Instructions Manual preview
K90-100
Бренд: Kenmore Страницы: 68
Kenmore K90-125 Owner'S Manual preview
K90-125
Бренд: Kenmore Страницы: 40
Palazzetti 805712550 Product Technical Details preview
805712550
Бренд: Palazzetti Страницы: 12
Potterton Boiler User Manual preview
Boiler
Бренд: Potterton Страницы: 12
Ideal Heating EVOMAX 2 100kW Product & Flue Manual preview
EVOMAX 2 100kW
Бренд: Ideal Heating Страницы: 29
STEELTECH Bruksanvisning Operating Instructions Manual preview
Bruksanvisning
Бренд: STEELTECH Страницы: 32
Chappee EDENA CLASSIC E 35 Installation And Servicing Instructions preview
EDENA CLASSIC E 35
Бренд: Chappee Страницы: 24
Viessmann Vitogas 200-F GS2 Service Instructions Manual preview
Vitogas 200-F GS2
Бренд: Viessmann Страницы: 40
Groupe Atlantic Melbury HE 10000 Installation, Use And Maintenance Instructions preview
Melbury HE 10000
Бренд: Groupe Atlantic Страницы: 34
Weil-McLain CGi Series 3 Installation And Maintenance Manual preview
CGi Series 3
Бренд: Weil-McLain Страницы: 72

Бренды по названию

Популярные бренды

Загрузить еще бренды