Raven RS1 Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 100

Raven RS1 Скачать руководство пользователя страница 7

CHAPTER

2

P/N 016-4010-001 Rev. A

3

CHAPTER 2

INTRODUCTION

Congratulations on your purchase of the Raven RS1 system! This system is designed to provide cutting-edge,

hands-free steering of the machine via Global Positioning System (GPS) coordinates.

The instructions in this manual are designed to assist in the proper calibration and operation of the RS1 system

when used with the Viper 4 or CR7 series field computers.

IMPORTANT:

Installation of the RS1 system must be completed before calibrating the system. If you have questions

regarding the installation of the RS1 system, refer to the machine-specific RS1 Installation Manual provided

with the installation kit.

IMPORTANT:

The Raven field computer must be calibrated specifically for the vehicle before being used to operate the

RS1 system. For questions about the field computer, refer to the Installation & Operation Manual provided

with the field computer.

INSTALLATION

RECOMMENDATIONS

Before installing the RS1 system, park the machine where the ground is level, clean, and dry. Bleed pressure from

the hydraulic system and leave the machine turned off for the duration of the installation process.

During the installation process, follow good safety practices. Be sure to carefully read the instructions in this

manual as you complete the installation process.

Raven Industries recommends the following best practices when installing or operating the RS1 system for the first

time, at the start of the season, or when moving the RS1 system to another machine:
• Verify that the machine’s hydraulic system is using fresh oil and that the filters have been recently changed
• Ensure there are no issues with the machine’s hydraulic system (e.g., pump issues, faulty hydraulic motors, fine

metal deposits in the hydraulic hoses, etc.) .

WARNING

Carefully read and follow all safety requirements

and precautions contained in this manual and the

machine-specific Installation Manual. Failure to

follow safety instructions may lead to equipment

damage, personal injury, or death.

«
...
5
6
7
8
9
...
»

Содержание RS1





































































































Отзывы:

Нет отзывов