Chapter 7
96
Envizio Pro and Envizio Pro II Installation and Operation Manual
Boom Master Options
The boom master options allow the operator to setup the preferred method to toggle recording of the coverage
map. Depending upon the product control system, the following options are available to configure the input of
the master switch used with the field computer:
None/Raven Serial Console
The following options are available if the product control options is set to either ‘None’ or ‘Raven Serial
Console’:
Note:
If the Envizio Pro or Envizio Pro II is connected to a CANbus with another CAN controller (such as
a Raven SCS 4400/4600) with AccuBoom, be sure the control interface option is set to ‘None.’
This option allows the field computer to monitor CANbus nodes without trying to control product
nodes. In this configuration, the boom master options will not be displayed.
Envizio Pro Boom Sense Wire.
Select this option if the boom sense wire has been connected as instructed in
the
Boom Sense Wire (Interface Cable Only)
On-Screen Vehicle Arrow.
This option allows the operator to touch the Vehicle Arrow
(shown to the right) displayed on the Guidance screen to toggle the coverage history on or
off.
AccuBoom™ Master Switch.
If the orange/white wire on the optional AccuBoom node
harness has been connected, select the ‘AccuBoom master switch’ option to create the coverage map based
upon the section information reported by the AccuBoom node.
CAN Options
If CAN Sprayer/Spreader Control is selected as the product control option, the list of available boom master
options is replaced by the following CAN AccuBoom options.
•
Do not select the ‘AccuBoom Combo Node’ option if an optional AccuBoom system has not been installed
on the CANbus.
•
AccuBoom Combo Node - If an AccuBoom system is installed and an AccuBoom combo node is present on
the CANbus, select this option. The following option will appear in the AccuBoom Options list.
•
Use as Boom/Speed AccuBoom Combo Node - This option will only appear if the ‘AccuBoom Combo Node’
option is selected. Select this option to use the AccuBoom combo node as the boom/speed node. If this
option is selected, a separate boom/speed node is not required for the CANbus system.
If ‘CAN AccuRow Only’ or ‘CAN Planter Control’ is selected, the boom master options displays the available
options for CAN Planter Control.
•
Reverse Sensing - Select this option to configure the field computer to detect when the vehicle direction is
reversed.
•
On-Screen Vehicle Arrow - This option allows the operator to touch the Vehicle Arrow
(shown to the right) displayed on the Guidance screen to toggle the coverage history on
or off.
•
AccuRow Master Switch - If an optional AccuRow system has been installed with the field
computer, select the AccuRow master switch option to create the coverage map based
upon the section information reported by the AccuRow node.
Содержание Envizio Pro
