manualshive.com logo in svg

Raven Case IH Patriot 3XX0, Руководство по установке системы управления и навигации

Поделиться
Скачать
Raven Case IH Patriot 3XX0 Скачать руководство пользователя страница 34

C

HAPTER

 5

32

Case IH Patriot 3XX0, Model Year 2010-2016 RS1™ HDU Guidance and Steering Installation Manual

FIGURE 15. Master Switch Installed

8. Install the master switch (P/N 063-0173-961) on the MASTER connector of the HDU switch harness cable.
9. Feed the harness and switch wires back into the console casing.
10. Press on the switch casing to ensure the switch is securely installed.

INSTALL THE FOOT SWITCH

FIGURE 16. Foot Switch Installed

1. Select a suitable location for the foot switch (P/N 063-0173-470) to be installed.

NOTE:

The foot switch should be installed in a location where the operator has easy access to it and is able 

to fully press the pedal.

2. Use the hole in the foot switch as a template, drill hoes in the floor of the cab.
3. Secure the foot switch to the floor by installing the suppled screws in each of the mounting holes.
4. Connect the ENGAGE connector on the HDU switch harness cable to the mating connector on the foot switch.

Содержание Case IH Patriot 3XX0











































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды