manualshive.com logo in svg

Raven Case IH Patriot 3XX0, Руководство по установке системы управления и навигации

Поделиться
Скачать
Raven Case IH Patriot 3XX0 Скачать руководство пользователя страница 30

C

HAPTER

 5

28

Case IH Patriot 3XX0, Model Year 2010-2016 RS1™ HDU Guidance and Steering Installation Manual

FIGURE 7. HDU Harness Cable Installed on HDU

2. Connect the gray 12-pin connector of the RS1 HDU harness cable to the mating port of the HDU (P/N 063-

0173-887).

FIGURE 8. POWER Connection

3. Connect the machine’s X-024M GPS POWER PORT connector (located in the fuse panel behind the operator’s 

seat) to the mating connector on the power adapter cable (P/N 115-0172-467).

4. Connect the other end of the power adapter cable to the RS1 HDU harness cable POWER connector.
5. Route the black 12-pin connector of the RS1 HDU Harness out of the grommet in the lower-right corner of the 

rear window. 

6. Route the black 12-pin connector up the back of the cab and along the roof. 
7. Connect the black 12-pin connector to the back of the RS1 unit. 

12-Pin HDU Harness 

(P/N 115-4010-056)

Connection

Содержание Case IH Patriot 3XX0











































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды