Raven AutoBoom 9600 Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 79

Raven AutoBoom 9600 Скачать руководство пользователя страница 7

CHAPTER

1

Manual No. 016-0230-096

1

CHAPTER 1

IMPORTANT SAFETY

INFORMATION

Read this manual and the operation and safety instructions included with your implement and/or controller

carefully before installing the AutoBoom™ system.
• Follow all safety information presented within this manual.
• If you require assistance with any portion of the installation or service of your Raven equipment, contact your

local Raven dealer for support.

• Follow all safety labels affixed to the AutoBoom system components. Be sure to keep safety labels in good

condition and replace any missing or damaged labels. To obtain replacements for missing or damaged safety

labels, contact your local Raven dealer.

When operating the machine after installing AutoBoom, observe the following safety measures:
• Be alert and aware of surroundings.
• Do not operate AutoBoom or any agricultural equipment while under the influence of alcohol or an illegal

substance.

• Remain in the operator’s position in the machine at all times when AutoBoom is engaged.
• Disable AutoBoom when exiting from the operator’s seat and machine.
• Do not drive the machine with AutoBoom enabled on any public road.
• Determine and remain a safe working distance from other individuals. The operator is responsible for disabling

AutoBoom when the safe working distance has diminished.

• Ensure AutoBoom is disabled prior to starting any maintenance work on AutoBoom or the machine.

• When starting the machine for the first time after installing AutoBoom, be sure that all persons stand clear, in

case a hose has not been properly tightened.

• The machine must remain stationary and switched off, with the booms unfolded and supported, during

installation or maintenance.

NOTICE

WARNING

CAUTION

«
...
5
6
7
8
9
...
»

Содержание AutoBoom 9600
















































































Отзывы:

Нет отзывов