Raven AutoBoom 9600 Скачать руководство пользователя страница 67 | Manualshive

Страница: 67 / 79

Raven AutoBoom 9600 Скачать руководство пользователя страница 67

5

Manual No. 016-0230-096

61

ULTRAGLIDE

5. Locate the machine’s center rack coil.
6. Disconnect the machine’s connections from the center rack control valve.
7. Install the center rack control boom sense adapter cable (P/N 115-0230-039) on the machine’s center rack

control coil.

8. Connect the machine’s connections to the installed center rack control boom sense adapter cable.
9. Connect the center rack control boom sense adapter cable to the Center Solenoid Up Sense and Control

connections on the AutoBoom harness cable.

CONNECT THE HARNESS CABLE TO THE SENSORS

1. Locate the Center Sensor connector on the AutoBoom harness cable.
2. Connect the Center Sensor connector to the installed center sensor (P/N 063-0130-018).
3. Locate the Left Outer Sensor connector on the AutoBoom harness cable.
4. Connect the Left Outer Sensor connector to the installed left sensor cable (P/N 115-0171-527).
5. Locate the Right Outer Sensor connector on the AutoBoom harness cable.
6. Connect the Right Outer Sensor connector to the installed right sensor cable.
7. If optional inside boom sensors are installed, repeat the steps above to connect the sensor cables.

CONNECT THE HARNESS CABLE TO THE IMPLEMENT EXTENSION TEE - GEN II CABLE ONLY

1. Route the harness cable (P/N 115-0230-085) toward the implement extension tee cable.
2. Connect the harness cable to the To Node connector.
3. Remove the terminator from the machine’s chassis harness or the standalone console harness.
4. Install the terminator on the remaining open end of the implement extension tee cable.
5. Refer to the wiring schematic (beginning on page 63) appropriate for the machine’s configuration to route the

implement extension tee cable.

6. Connect the implement extension tee cable to the location determined in the step above.

CONNECT THE HARNESS CABLE TO THE CONTROLLER CABLE - GEN I CABLE ONLY

1. Route the harness cable (P/N 115-0230-045) toward the machine’s cab.
2. Connect the harness cable to the controller cable (P/N 115-0230-007).
3. Tighten the connector screw cap to secure the connection.

CONNECT THE CONTROLLER (IF APPLICABLE) - GEN I CABLE ONLY

1. Route the controller cable (P/N 115-0230-007) into the right side of the machine’s cab.
2. Locate the two controller connectors and connect them to the AutoBoom controller (P/N 063-0130-021).

NOTE:

The AutoBoom controller should be mounted in the machine’s cab so that the machine’s operator

has easy access to it.

CONNECT THE FIELD COMPUTER (IF APPLICABLE)

Refer to the Installation & Operation Manual and the appropriate wiring schematic beginning on page 63 for

installation and wiring instructions for your specific field computer.

CONNECT THE POWER LEADS

1. Locate the power cable that has the power and ground leads at one end.
2. Disconnect the machine’s connectors from the battery terminals.

«
...
65
66
67
68
69
...
»

Содержание AutoBoom 9600
















































































Отзывы:

Нет отзывов