background image

2524 ChronoCom  Programming

Table 1. Clock Modes A-P

Table  4. Cross-Reference to tbe Major Functions

Function

Call-in configuration

Mode

Mode E.

Intercom Mode 

3.

Call-in sensitivity

 Intercom Mode 5.

Clock Codes

I

Modes A 

and B.

Clock-event entry.

 Clock Mode 

3.

Clock-event detailed re- Clock Mode 4.

view and edit.

Holiday-event detailed re- Mode D.

E

F Display the number of events and

holiday entries; erase them all.

Holiday-event overview Mode F.

and erase all.

Table 2. Clock Modes l-6

Monitoring

I

Intercom Mode 2-4. Acti-

vated in Intercom Run

Mode

I

Date.

Function

Music Clock Modes 

and 4

 2

Numbers: room (Architec-

 

 Intercom Modes 1 and 2.

tural) and line  (physical)

 3 

 Enter Events.

I 4

 Review, edit, or delete events.

Schedules

 Clock Modes 

3,4,

 and 6.

 5

 Duration for each zone.

Supervision

Intercom Modes 2 and 

3

6 Select active zones and schedules.
7

[Future.]

Time 

and date. 

Clock Mode 1.
Modes C and D

Time-change (Daylight
Savings)
Time-correction

 8 

[Future.]

I

[Future. ]

Mode A.
Clock Modes 

3, 4, 5,

 and 6.

Reduced by codes in Mode

A. Clock Modes 

3-6; 

Modes

C and D.

Zones
Zones for clock events.

Table 

3. 

Intercom Modes

Intercom Mode 2.

Zones for paging.

Mode

Function

Table 5. Factory Settings

Mode Setting

A Correction Code “0 1”

E No. of SC’s = 0; Comm. Scanning disabled

Clock 5

“03” sec., all zones

Clock 6 Zones l-6 selected; Sched. 1

Comm. 

Mon., Sup., Auto Answ., & Rem. Ph. dis-

abled; normal and priority call-in enabled

Comm. 4 Monitor dur.: “03” seconds

Notes for 

Table  5: 1. The 

time 

and dnte nre not set, nnd no

events or station programming are entered.

2. In “Comm” Mode 

3, 

only 

the two call-in types are enabled.

These will not run unless Mode E is changed.

 However, 

should

the “Comm” function be activated, these  two call-in 

types will

usually be wanted.

1

Architectural 

Number for each speaker.

2 Enter and review intercom zones; moni-

tor and supervision bits for each speaker.

3

Enable or disable the system’s monitor

and supervision functions.

I 4

 Duration for monitoring.

I 5

 Adjust call-in sensitivity.

6 [Future.]
7 [Futute.]
8 [Future.]

[Future.]

Page 14

4/90

Содержание 2524 ChronoCom


















Отзывы: