Rattler 250 Скачать руководство пользователя страница 4

Страница: 4 / 16

This wire should be connected to the (+) parking light wire. This output is protected with a 10 amp fuse. Never

increase the value of the light flash fuse. If more current is required, use an external relay.

NOTE:

When connecting this wire to a (-) parking light wire, a relay is required. See the following

diagram for the relay application.

This wire provides a (-) 200 mA output whenever the transmitter code controlling Channel 3 is received. This

output will continue as long as that transmission is received. Use for options such as 551T Valet Start system,

529T or 530T power window controllers, etc.

IMPORTANT!

Never use this wire to drive anything except a relay or a low-current input! The tran-

sistorized output can only provide 200 mA of current, and connecting directly to a solenoid, motor,
or other high-current device will cause it to fail.

Connect this wire to the optional domelight supervision relay as shown in the following diagram.

H1/4 BLACK/WHITE (-) domelight supervision relay output

H1/3 WHITE/BLUE (-) channel 3 validity output

H1/2 WHITE (+) light flash output

Содержание 250

















Результаты поиска

Содержание 250

Отзывы:

Похожие инструкции для 250

Бренды по названию

Популярные бренды

Rattler 250, Руководство по установке

Результаты поиска

Содержание 250

Отзывы:

Похожие инструкции для 250

Бренды по названию

Популярные бренды