Rattler 250 Скачать руководство пользователя страница 3

Страница: 3 / 16

primary harness (H1), 12-pin connector

The primary harness is the standard 12-pin harness used by DEI security systems.

______

The functions of all the wires that are used in the primary harness are outlined in this section.

This wire supplies (-) ground as long as the system is armed. This output ceases as soon as the system is dis-

armed. This wire can be used to turn on an optional sensor or to control an optional accessory, such as a window

module or pager.

H1/1 ORANGE (-) ground-when-armed 500 mA output

primary harness (H1) wire connection guide

RED/WHITE

(-) 200 mA CHANNEL 2 VALIDITY OUTPUT

RED

(+)12V CONSTANT POWER INPUT

BROWN

(+) SIREN OUTPUT

YELLOW

(+) IGNITION INPUT, ZONE 5

BLACK

(-) CHASSIS GROUND INPUT

VIOLET

(+) DOOR TRIGGER INPUT, ZONE 3

BLUE

(-) INSTANT TRIGGER, ZONE 1

GREEN

(-) DOOR TRIGGER INPUT, ZONE 3

BLACK/WHITE

(-) 200 mA DOMELIGHT SUPERVISION OUTPUT

WHITE/BLUE

(-) 200 mA CHANNEL 3 VALIDITY OUTPUT

WHITE

(+) LIGHT FLASH OUTPUT

ORANGE

(-) 500 mA GROUND-WHEN-ARMED OUTPUT

H1/1

H1/2

H1/3

H1/4

H1/5

H1/6

H1/7

H1/8

H1/9

H1/10

H1/11

H1/12

primary harness (H1) wiring diagram

Содержание 250

















Результаты поиска

Содержание 250

Отзывы:

Похожие инструкции для 250

Бренды по названию

Популярные бренды

Rattler 250, Руководство по установке

Результаты поиска

Содержание 250

Отзывы:

Похожие инструкции для 250

Бренды по названию

Популярные бренды