Rattler 250 Скачать руководство пользователя страница 11

Страница: 11 / 16

operating settings learn routine

Many of the operating settings of this unit are programmable. They can be changed whenever necessary through

the Operating Settings Learn Routine. The Valet/Program push-button switch, plugged into the blue port, is used

together with a programmed transmitter to change the settings.

The Operating Settings Learn Routine dictates how the unit operates. It is possible to access and change any of

the feature settings using the Valet/Program switch.

To enter the System Features Learn Routine:

Open a door. (

The GREEN wire, H1/5, or the VIOLET, H1/7 must be connected.)

Ignition.

Turn the ignition on, then back off. (The H1/9 YELLOW switched ignition input

must be connected.)

Choose.

Within 10 seconds, press and release the Valet/Program switch the number of

times corresponding to the feature number you want to program (see the

Features Menu

section of this guide). The LED ON settings listed in the

Features Menu

table are the factory

default settings.

Once the Valet/Program switch has been pressed and released the number of times corre-

sponding to the feature you wish to program, press it once more and

HOLD

it. After one

second, the LED will flash to indicate which feature you have accessed. For example, groups

of five flashes would indicate access to Feature 5. The siren will also chirp five times.

Transmit.

While

HOLDING

the Valet/Program switch, you can select the desired feature set-

tings using the remote transmitter. As shipped, the unit is configured to the default LED

ON settings. Pressing Button I while

HOLDING

down the Valet/Program switch will program

a feature to the LED ON setting. The siren will chirp once to indicate the one-chirp setting

has been selected. Pressing Button II while

HOLDING

down the Valet/Program switch will

change a setting to the LED OFF setting. The siren will chirp twice indicating that the LED

OFF setting has been selected.

Release.

Release the Valet/Program switch.

Содержание 250

















Результаты поиска

Содержание 250

Отзывы:

Похожие инструкции для 250

Бренды по названию

Популярные бренды

Rattler 250, Руководство по установке

Результаты поиска

Содержание 250

Отзывы:

Похожие инструкции для 250

Бренды по названию

Популярные бренды