background image

REV.  1/25/08 

Page 1 of 7

 

 
 
 
 
 
                    

       

 

 
 
 

THR-2R INSTALLATION AND OPERATING INSTRUCTIONS

 

 

MULIT-FUNCTION WIRELESS REMOTE CONTROL SYSTEM 

FOR OPERATING A LATCHING SOLENOID VALVE, MANUALLY OR WITH A THERMOSTAT FUNCTION 

 

 
 
 
 
 

INTRODUCTION 

 
This  remote  control  system  was  developed  to  provide  a  safe,  reliable,  and  user-friendly  remote  control  system  for  gas  heating 
appliances.  The system is operated manually from the transmitter.  The system operates on radio frequencies (RF) within a 20' range 
using non-directional signals.  The system operates on one of 1,048,576 security codes that are programmed into the transmitter at the 
factory; the remote receiver's code must be matched to that of the transmitter prior to initial use.  

 
 
 
 
 
TRANSMITTER 

 

This remote control SYSTEM offers the user a battery-operated remote control to 
power  a  latching  solenoid  such  as  those  used  with  gas  valves  used  in  some 
heater rated gas logs, gas fireplaces and other gas heating appliances. 
 
The  solenoid  circuit  uses  the  battery  power  from  the  receiver  to  operate  a 
solenoid.  The circuit has reversing polarity software which reverses the positive 
(+)  and  negative  (-)  output  of  the  receiver's  battery  power  to  drive  a  latching 
solenoid ON/OFF. The SYSTEM is controlled by the remote transmitter. 
 
The transmitter operates on a (2) 1.5V AAA batteries.  
 
It is recommended that ALKALINE batteries always be used for longer battery life 
and maximum operational performance. 
 
Before  using  the  transmitter,  install  the  (2)  AAA  transmitter  batteries  into  the 
battery  compartment.  (Use  caution  that  batteries  are  installed  in  the  proper 
direction) 
 
 
 
 
 
 

 

KEY SETINGS 

 

 

ON      - Operates unit to on position, Manually operated solenoid ON. 

      OFF      - Operates unit to off position, Manually operated solenoid OFF. 
      MODE  - Changes unit from manual mode to thermostat mode. 
      SET      - Sets temperature in thermostat mode. 

 

ON

MODE

OFF

SET

1

2

3

4

 

IF YOU CANNOT READ OR UNDERSTAND THESE INSTALLATION INSTRUCTIONS DO NOT 

ATTEMPT TO INSTALL OR OPERATE  

 

ON

MODE

OFF

BUTTON

WALL CLIP

SLOT

BATTERY

COMPARTMENT

FRONT

BACK

OFF

SET

ON

BUTTON

MODE

BUTTON

SET

BUTTON

 

Review 

COMMUNICATION SAFETY SECTION

 under TRANSMITTER section under REMOTE RECEIVER section.  This signal safety 

feature shuts down the fireplace system when a potentially unsafe condition exists.

 

f i r e - p a r t s . c o m

Содержание THR-2R








Отзывы: