background image

5

Additional Parts Required:  

•  1” (25 mm.) or 1 1/2” (38 mm.) I.D. discharge hose 

•  3/4” (19 mm.) I.D. reinforced intake hose 

•  3/4” (19 mm.) and 1” (25 mm.) or 1 1/2” (38 mm.) hose 

clamps (two for each connection below waterline) 

•  Wire

•  Terminals 

•  Fuse/circuit breaker

Parts included with all  models:

1.   Toilet bowl assembly

2.   Mounting bracket kit

3.   Seat 

4.   Flush control - includes User and Installation 

guides. (In some cases distribution points 

may package and sell controls seperatly.)

5.   User guide and Installation guide with labels

       

Additional Parts included with sea water model:

1.   Remote pump assy.

2.   Relay for remote pump (Momentary Flush 

Switch and SeaFresh models only)

SIZE inch (mm.)

MOUNTING

Mounting Toilet

Mounting surface must be flat and solid.

Seat must open more than 90 degrees.

1. 

Place the toilet and mark mounting holes’ center 

line, and outside of the bowl (FIG 1). Draw a 

center line between two holes.  Mark front hole 

outside and center and draw a line perpendicular 

to first center line.

2.    Mark three  lines A, B, and C,  3/8” from outside 

lines.

3.   Line up outside edges of the brackets  with 

marked lines A, B, and C.

4

Secure bracket assembly to deck. Using three #14 

self threading bolts and flat washers. Other types 

of fasteners may be used if so desired.

 

Note

: place bolts as close to mark lines A, B,and 

C as possible 

5.     Drill holes for discharge hose (2”(51 mm.) for 1 

1/2” hose; 1 1/2”(38 mm) for 1” hose), inlet hose 

(7/8” (22 mm.) and wires (3/4”(19 mm.) using 

dimensions shown in FIG 2.

 

Note: check outside diameter of the hoses and 

adjust hole sizes accordingly.

 6.     Complete  plumbing and wiring before installing 

toilet.

FIG 1

L490  0720jlc                                                                                                             

13

8

 [35]

1

4 [6]

2 [51]

WIRES

INLET HOSE

DISCHARGE HOSE

Bolt and 
Washers

Line A

Line C

Line B

See #5 under Mounting

See #5 under Mounting

See #5 under Mounting

25

8

 [67]

3 [76]

inch [mm]

FIG 2

Содержание Marine Elegance Toilet













Отзывы: