Raritan DOMINION SX -, Инструкция по установке и эксплуатации

Страница: 82 / 172

72 D
OMINION
SX I
NSTALLATION AND
O
PERATIONS
M
ANUAL
is necessary to enter only the port number. The short form of the command is lp . Once the console
command has been issued there are additional commands as follows:
•
When a user presses the Escape sequence keys, the control goes to a menu for the console session. The
user is presented with a prompt for the console menu (Admin:Port0:Command>). The following
commands can be executed from this menu:
−
send_break - intended to be used for SUN targets. It sends “break” command to the serial target
(SUN workstation or server).
−
get_history - used to get the history for the console session – from the port buffer, which is
accumulating console output even when there is no connected user on that port. Each Dominion
SX port has an independent port buffer. The history can be copied and pasted into another
program for off-line analysis.
−
get_write – allows users to request write access to the port when in a port-sharing session; shortcut
is
gw .
−
Help - displays help for console menu.
−
Quit - quits console session and returns to the main menu.
Note : Pressing the < Enter > (Carriage Return) key shall return control back to console session from the
console menu.
2. list_ports : displays the list of available ports. Only ports that the user is authorized to see are on the
displayed list. The displayed list contains the port name (as assigned by the user to the port) and the
application associated with it.
3. change_escape : used to change the escape character used to exit from the serial target session. For
example if the user has connected to a serial target at port 2 using “console_cmd 2”, then the escape
character can be used to come back to menu prompt “RaritanCommand>”
Default Escape Character is CTRL [i.e., Press CTRL key ]. The escape character can be a single key
or a combination of “Ctrl” key and another key from the following set [‘@’, ‘a – z’, ‘A – Z’, ‘[‘, ‘]’, ‘\’,
‘^’, ‘_’]. Using a single-key for the escape sequence is strongly discouraged.
4. help or h or ? : displays the list of supported commands.
5. user_list - displays list of all configured users; shortcut is ul
6. log <start|stop|clear|status> - used to start/stop/clear or get status of syslog (use cfglog command to
configure syslog)
7. cfglog <[local <wrap|flat> [FILE SIZE]] | [remote [SERV1] [SERV2]]> - used to configure location
and size of syslog (use log command to start/stop/clear or get status of syslog); currently, local logging
should not be used.
8. tacacs_cfg <enable|disable|status> [<SERVIP> <ServerPort> <keyString>] - used to configure
remote authentication and authorization, or to get status.
9. nfsportlog <enable|disable|status> [<PREFIX> <SIZE> <SERV1> <SERVDIR> [<SERV2>
<SERVDIR2>] - used to configure NFS session/port logging.
10. snmp [<<enable|disable> [COMM_NAME]|<add|del> RECIPIENT>] - configuration of SNMP traps.
11. lpa [<enable|disable|status> [BPS]] – Enable/Disable/Set speed in bits per second (BPS) and show
status of local port access (connection of VT100 terminal/PC/workstation with communications
software to serial port on SX unit).
12. quit : exit from SSH session.
Note : Use the standard SSH exit sequence “~.” to exit from SSH session at any time.
Some of the usage scenarios using command line SSH client:
#SSH –l dominion <IP Address Of Dominion SX>
Welcome to Raritan Dominion Server
Username: admin
password:
Authenticating [admin].....Authenticated.
Type [help] for all commands